No products in the cart.
Regulator filter model PP3
liquid air
Maximum operating pressure (MPa) 1.0 (140psi)
Constant pressure (MPa) 1.5 (200psi)
Standard pressure setting 0.05~1.0 (7~140psi)
(MPa) Customized specifications 0.05~0.2 (7~30psi), 0.05~0.4 (7~60psi), 0.05~1.2 (7~170psi)
Ambient and fluid temperature (℃) -5 ~ 60 (23 ~ 140 °F) (non-freezing)
Flow capacity ※ 1/4˝ 2100 (74scfm)
(Nℓ/min) 3/8˝ 2,600 (92scfm)
Filtration (㎛) 5
Soothing style of construction
Polycarbonate bowl material
Nylon bowl protective material
Discharge Capacity (㎤) Manual Drain: 38 (1.28 oz), Auto Discharge: 30 (1.01 oz)
Weight (kg) 0.49 (1.08 lbs)
Zur Wunschliste hinzufügen
Zur Wunschliste hinzufügen
Categories: brand, filteration, Pneumatic, regulator water catch (regulator filter), TPC, TPC filtration
Marke: TPC
Beschreibung
Regulator filter model PP3
PP3 model regulator filter is another component of the industrial system. This part is used in places where there are pneumatic systems. The air around us that we breathe has some moisture.
When this air is compressed, the moisture along with it is also compressed.
The compressed moisture is collected at the bottom of the compressor, but still a large amount of it is transferred by air to the equipment. Moisture seriously damages the equipment. Filters filter this moisture and do not allow moisture and contamination to be transferred to the equipment.
The collected water is collected in the filter cup or is drained by the automatic drain. The air that has been filtered must be brought to the right pressure and its pressure must be reduced and actually regulated. The act of regulating is done by the regulator (pressure breaker) and the air is filtered and transferred to the equipment with the right pressure.
PP3 model regulator filter sizes
Filter regulators are in different sizes and models, which include the following items.
1. The filter sizes of the regulators are: 3″, 2″, 1″, 3/4″, 1/2″, 3/8″, 1/4″, 1/8″.
2. Drainage of moisture (water) in manual draining models, semi-automatic draining and fully automatic draining. Air regulator filter structure:
The air regulator filter consists of several main parts, which include the following:
1. Inlet air adjustment regulator along with wind indicator to observe the inlet air pressure
2. 5 micron fiber or brass filter to capture air moisture and the moisture holding chamber separated from the incoming air
3. The outlet port for the discharge of moisture separated from the inlet air, the filter function of the air regulators:
The function of the regulator filter is that the incoming air enters the air adjustment regulator, which can be adjusted from 10 to 0 bar by the air pressure regulator.
Regulator filter model PP3
Regulator filter model PP3
Then, after passing through the regulator, the incoming air enters the 5 micron dehumidifier filter and is separated by the incoming air humidity filter, and the dry air without any moisture is directed to the regulator filter outlet and then transferred to the ventilation system.
Filter regulator model PP3 or Filter Regulator is one of the industrial parts in the important care unit that is used in many small and large industries. The accuracy and application of standards are important indicators of any industry, and in better words, the lack of these two indicators can create important challenges and disturbances.
Industry and engineering have a direct and continuous relationship with each other, and since measurement accuracy is one of the most important discussions in engineering, as a result, in industry, which is dependent on engineering plans, measurement and accuracy are of great importance. . In the industry, the more accurate the measurement, the less the percentage of errors and the higher the efficiency and also the success of the project.
In other words, in the industry and production, there are indicators and standards that must be followed seriously. To comply with these standards, specialized companies are working all over the world and each of them produces special parts. In simpler terms, various tools are designed to apply accurate measurements in industries, and several pieces together manage and control a part of an industry.
The scope of diversity of measuring instruments in industries is very large. Some of these tools have the ability to measure instantaneously, and by using today’s technologies, such as digital data, they announce the instantaneous measurement, and some other instruments also have a mechanical function, but they are designed and produced based on engineering principles. are
Standard working conditions of filter regulator model PP3
The regulator filter can be used at a temperature of +40 to -5 degrees Celsius and with a fluid pressure of 10 to 0 bar. Note that if the incoming air is stained with oil or grease, the dehumidifier filter will be greased and unable to absorb moisture.
Uses of PP3 model regulator filter:
The reason for using filter regulators in the ventilation system is to separate moisture from the air, because if the air used contains moisture, it will cause irreparable problems, which we will mention a few of:
1. Rotting and loss of all O-rings and packings in the air steering jacks and valves and oxidation, rotting and rusting of the body of the air steering jacks and valves.
2. In the paint industry, we can mention the creation of water holes, the unevenness of the paint surface and many different problems. He pointed out in machine building, food, pharmaceutical, health, construction, oil, gas, petrochemical and other industries.
Criteria for the regulator filter stone material:
Filter material (brass filter-felt filter)
Filter micronization (from forty microns to one hundredth of a micron)
Appearance and dimensions of the filter
Usually, filter stone (filter element) with 40 or 20 micron is used in the filter of existing regulators.
20 micron stone is used in felt filters.
Definition of Prerequisite Care Unit Introduction of Filter Regulator
The filter regulator is one of the parts used in the maintenance unit of pneumatic systems. In this article, the care unit is the same as the pneumatic care unit, and we intend to introduce one of the most important parts of this section, the regulator filter.
Pneumatic systems are used in various industries and in industrial machines. Pneumatic systems, like their importance, are sensitive to different conditions, including polluted and humid air, and they must be supplied with healthy air in order to have proper efficiency, for this reason, different parts are used to create suitable conditions, which are a unit It is called care.
The care unit is a set that aims to design
Its essence is to create suitable conditions for the operation of the pneumatic system. This care unit includes parts such as regulator, filter regulator and oiler. Among the most important types of care units that are popular in the Iranian market, we can mention these brands:
Metal work made in Italy
Airtech
SKP South Korea
Festo Germany
Aventics (Germany)
Aignep (Italy)
Shako
Filter Regulator is the main topic of this article, and in the rest of this text, we intend to provide specialized information about the filter regulator, but since the Filter Regulator is related to other parts of a pneumatic care unit, at first, briefly We will introduce other components of this care unit, such as oiler and regulator.
Introduction to the introduction of PP3 model regulator filter
The PP3 model regulator filter is one of the parts that is used in the pneumatic system care unit along with the oiler. In the pneumatic systems care unit, different parts must work together so that the overall process of a project is done well.
For this reason, the compactness of the work and the proximity of the parts can cause friction and locking of a part and disrupt the functioning of a set. In order to solve this problem and prevent disruptions in the work of the care unit as well as serious breakdowns of the devices, it is recommended that oil-consuming parts be lubricated in defined time intervals by a specialized device.
To do this, the lubricant is used in the care unit. In fact, to inject oil into parts such as actuators and valves, the required oil is injected into the system’s compressed air by the lubricator. The lubricating oil consists of different parts and by means of it the required amount of oil can be injected into the system.
Different oils can be injected into a pneumatic system by using an oiler. Choosing the type of oil and its amount is an important and specialized issue that the experts of a project should decide on.
Getting to know the regulator, introduction to the introduction of the regulator filter
PP3 model regulator filter is one of the main parts of industrial regulators. And to get to know this piece, we need to get to know the regulator first. Regulator (in English regulator) is a word that is derived from the word regulate which means flow regulator. In other words, a regulator is a part that is used to control and adjust the input of a material to a system.
These inputs can include vaporized liquids, gases, and even electrical voltages. In general, the regulator adjusts the flow to a system with a certain amount of pressure determined for it. Due to the fact that the input material to the regulators is different, and the systems in which the regulators are used are different and wide, as a result, various examples of the regulator have been produced, among which the following can be mentioned:
Gas regulator
Electric regulators
Fluid regulators
Filter Regulator The PP3 model gas or pneumatic regulator filter is a part that is mainly used for industrial and household regulators. In general, regulators are divided into two categories: household and industrial regulators, which are familiar to all of us and are parts that are used to adjust the gas pressure of cylinders and household gas in general, but in contrast to these small parts, professional industrial regulators are located
Industrial regulators are usually produced for large tanks and high pressures. These regulators have special features according to the industry they are used in. For example, these regulators must be made of resistant materials and have resistance against gases, corrosive liquids, and sometimes toxic and putrid.
Industrial regulators are equipped with various parts, one of the most important of which is the filter regulator PP3 model, which we will introduce in the rest of this text.
Types of regulator filters
PP3 model regulator filter is a small but very important industrial part that plays an effective role in performing various operations of a project. In fact, this part is considered a part of the monitoring unit of a system. Gas or pneumatic regulators are the most common types of regulators used in the industry. These regulators need an important part to apply standardization of intake air for proper and principled operation, and this important part is the regulator filter.
The PP3 model regulator filter is a part that is necessary for the operation of the regulator. In fact, the air in the environment that we breathe contains some moisture. Humidity is the amount of heat present in a unit volume of air.
Air enters pneumatic systems in a compressed form and this problem causes the accumulation of moisture in these systems, especially the bottom of the compressors, as a result of which decay and failure occur in these equipments. Filter Regulator is used to prevent this unpleasant event. The PP3 model regulator filter absorbs the moisture in an inlet and makes the system work better.
Filter Regulator as an important part is made up of different parts. For example, the water in the inlet gas accumulates in the filter cup over time and is drained manually or automatically depending on the type of filter.
A filter regulator is also used to prevent dust from entering a pneumatic system. In some areas as well as work environments, dust is part of the environmental conditions, for this reason, the work systems of a project are taken care of by this part. Filter Regulator Filter regulator model PP3 b
As an important functional part in regulators, it is produced from various raw materials and has various sizes that should be selected and purchased based on the type of regulator.
Regulator filter model PP3
Regulator filter model PP3
PP3 model regulator filter as an important part of an industrial regulator, and a part of the care unit of a system, can be classified in different ways. For example, this important part is produced from different raw materials, which must be resistant to different environmental conditions. Among these materials, we can mention brass metal as well as felt filters. As a result, the type of raw materials can be considered as a factor for the division of regulator filter types.
The regulator filter is also produced in different sizes. Each size is used in certain systems and cases. The most important sizes of the PP3 filter regulator can be one inch, three-quarters of an inch, one-quarter of an inch, one-half of an inch, one-eighth of an inch, three-eighths of an inch, two inches, one and a half inches, and one and a quarter. Inch pointed.
Of course, two-part sizes such as three-quarter inches are available in one piece and sizes such as one and a half inches are offered in two pieces due to their larger dimensions and are used in certain systems.
The PP3 model regulator filter is a piece that absorbs the moisture in the compressed air and must be drained after reaching the set amount. The discharge of this part is done manually and automatically, and for this reason, the regulator filters are also produced in two types, automatic and manual.
Filter Regulator PP3 model regulator filter is an industrial piece that is produced by various companies around the world today and each brand claims to produce quality products, for this reason, regulator filters can be divided into different categories based on the production brand. divided But in general, it is recommended to buy reliable and quality brands only through reliable sales centers.
Important points on how to install PP3 model regulator filters
PP3 model regulator filter is considered as one of the main and important parts of devices based on pneumatic systems, whose malfunction can cause irreparable damage to a project and its machines. This is one of the most important points that should be taken into account when buying the PP3 filter regulator. As a result, it is necessary to buy a quality and suitable piece.
The PP3 model regulator filter is a part that is produced in different models and capacities, and for this reason, in the first step of buying a regulator filter, you should know your needs so that you can make a successful purchase based on your real and correct needs. . Since the regulator is produced in a variety of different models, it is necessary to purchase a suitable size filter for a regulator.
Filter Regulator PP3 filter regulator is available in different types and brands with different prices. Naturally, most buyers tend to make their purchase with the best quality and the most suitable price. But the important thing is to buy regulator filters with a sales guarantee. Most of the big companies producing this part offer their products with a sales guarantee, it is recommended to pay attention to the warranty of the purchased product when buying.
The filter regulator model PP3 is a part that is produced today by various companies around the world, and some of these brands produced by professional companies are well-known and popular, but in addition to the popular brands Filter Regulator, the filter regulator model PP3, There are also low-quality samples whose use can endanger the health of work and parts of a project.
For this reason, it is recommended to visit reputable agencies to buy popular and well-known brands of industrial regulator filters. Today, due to the importance of this part in different industries, agencies of different brands have been set up in different provinces of Iran that offer quality products.
Advantages of buying Filter Regulator from reputable dealers
The PP3 model regulator filter is an important part that can be purchased in different ways in the market. Usually, industrial supply stores supply this part like other tools and parts in a normal way, and they do not accept any obligation against product failure or after-sales service, and this issue can be changed in the future. In case of possible failure of the part, it will be to the detriment of the buyers.
For this reason, it is recommended to buy all kinds of regulator filters from reputable dealers. Among the most important advantages of buying this product from reputable dealers are the following:
Buy the original products of each brand: To buy a specific brand of PP3 model regulator filter, you must visit the authorized dealers of the same brand.
For example, some reputable and best-selling brands of filter regulator, PP3 model, have attracted the attention of profit-seeking collections in East Asian countries, and counterfeit samples from reputable brands have entered the market, which unfortunately look similar to the original samples, and that’s why The reason is to avoid unknowingly buying fake products, it is recommended to buy from reputable dealers of the desired brand.
Buy PP3 model regulator filter at a great price: PP3 model regulator filter is a product that has different prices in different stores, but to buy any brand at the best price, it is recommended to visit official dealers.
Receiving after-sales service: The regulator filter is a part that must be installed
Install it according to the defined standards. Usually, in the official agencies of different brands of PP3 regulator filter, there are people who can give you free advice and guidance to buy the right product and how to install it.
[caption id="attachment_5080" align="aligncenter" width="826"]
فیلتر رگولاتور مدل PP3[/caption]
Zusätzliche Informationen
| برند ها |
|---|
Quick Comparison
| Settings | Regulator filter model PP3 remove | SQ model automatic fitting remove | DPSA model digital pressure switch remove | SP4000 large body metal flow control remove | Silencer (BC sintered) SNB remove | SP2000 small body metal intermediate flow control remove | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Name | Regulator filter model PP3 remove | SQ model automatic fitting remove | DPSA model digital pressure switch remove | SP4000 large body metal flow control remove | Silencer (BC sintered) SNB remove | SP2000 small body metal intermediate flow control remove | ||||||||||||
| Image | |  |  |  |  |  | ||||||||||||
| SKU | ||||||||||||||||||
| Rating | ||||||||||||||||||
| Price | ||||||||||||||||||
| Stock | ||||||||||||||||||
| Availability | ||||||||||||||||||
| Add to cart | ||||||||||||||||||
| Description | liquid air Maximum operating pressure (MPa) 1.0 (140psi) Constant pressure (MPa) 1.5 (200psi) Standard pressure setting 0.05~1.0 (7~140psi) (MPa) Customized specifications 0.05~0.2 (7~30psi), 0.05~0.4 (7~60psi), 0.05~1.2 (7~170psi) Ambient and fluid temperature (℃) -5 ~ 60 (23 ~ 140 °F) (non-freezing) Flow capacity ※ 1/4˝ 2100 (74scfm) (Nℓ/min) 3/8˝ 2,600 (92scfm) Filtration (㎛) 5 Soothing style of construction Polycarbonate bowl material Nylon bowl protective material Discharge Capacity (㎤) Manual Drain: 38 (1.28 oz), Auto Discharge: 30 (1.01 oz) Weight (kg) 0.49 (1.08 lbs) | ● ONE ACTION inserts tube for easy attachment and release
● The volume and OD are smaller than the conventional type, but the same flux is obtained
● Surface treated with electroless nickel plating for excellent corrosion resistance
● The oval sleeve is designed to be easily released in confined spaces
● The screw part has O-rings or has a sealant coating
● Small fittings for small appliances and piping in confined spaces
|
▪ Digital pressure sensor with high accuracy
▪ LCD screen with high brightness.
▪ High resolution: 1/1000 ▪ Convertable pressure unit - Combination pressure: kPa, kgf/cm2, bar, psi, mmHg, mmH2O, inHg - Standard pressure: kPa, kgf/cm2, bar, psi, Mpa
▪ Different output modes: Hysteresis mode, One point selting mode. 2 independent output mode, comparative window output mode
▪ Prevent chatter for output (selectable response time: 2.5, 5, 100, 500 milliseconds)
▪ Analog output scale function (1-5VDC).
▪ Reverse polarity protection circuit and excess current
▪ Zero point setting function ▪ Display peak and hold low
| ● The holder prevents accidental loss of the needle
● Compact size saves space
● Speed must be carefully controlled even at low speed
● Lock nut
● Copper free type for electronics industry (optional)
|
| ● The holder prevents accidental loss of the needle
● Compact size saves space
● Speed must be carefully controlled even at low speed
● Lock nut
● Copper free type for electronics industry (optional)
| ||||||||||||
| Content | Regulator filter model PP3 PP3 model regulator filter is another component of the industrial system. This part is used in places where there are pneumatic systems. The air around us that we breathe has some moisture. When this air is compressed, the moisture along with it is also compressed. The compressed moisture is collected at the bottom of the compressor, but still a large amount of it is transferred by air to the equipment. Moisture seriously damages the equipment. Filters filter this moisture and do not allow moisture and contamination to be transferred to the equipment. The collected water is collected in the filter cup or is drained by the automatic drain. The air that has been filtered must be brought to the right pressure and its pressure must be reduced and actually regulated. The act of regulating is done by the regulator (pressure breaker) and the air is filtered and transferred to the equipment with the right pressure. PP3 model regulator filter sizes Filter regulators are in different sizes and models, which include the following items. 1. The filter sizes of the regulators are: 3", 2", 1", 3/4", 1/2", 3/8", 1/4", 1/8". 2. Drainage of moisture (water) in manual draining models, semi-automatic draining and fully automatic draining. Air regulator filter structure: The air regulator filter consists of several main parts, which include the following: 1. Inlet air adjustment regulator along with wind indicator to observe the inlet air pressure 2. 5 micron fiber or brass filter to capture air moisture and the moisture holding chamber separated from the incoming air 3. The outlet port for the discharge of moisture separated from the inlet air, the filter function of the air regulators: The function of the regulator filter is that the incoming air enters the air adjustment regulator, which can be adjusted from 10 to 0 bar by the air pressure regulator. Regulator filter model PP3 Regulator filter model PP3 Then, after passing through the regulator, the incoming air enters the 5 micron dehumidifier filter and is separated by the incoming air humidity filter, and the dry air without any moisture is directed to the regulator filter outlet and then transferred to the ventilation system. Filter regulator model PP3 or Filter Regulator is one of the industrial parts in the important care unit that is used in many small and large industries. The accuracy and application of standards are important indicators of any industry, and in better words, the lack of these two indicators can create important challenges and disturbances. Industry and engineering have a direct and continuous relationship with each other, and since measurement accuracy is one of the most important discussions in engineering, as a result, in industry, which is dependent on engineering plans, measurement and accuracy are of great importance. . In the industry, the more accurate the measurement, the less the percentage of errors and the higher the efficiency and also the success of the project. In other words, in the industry and production, there are indicators and standards that must be followed seriously. To comply with these standards, specialized companies are working all over the world and each of them produces special parts. In simpler terms, various tools are designed to apply accurate measurements in industries, and several pieces together manage and control a part of an industry. The scope of diversity of measuring instruments in industries is very large. Some of these tools have the ability to measure instantaneously, and by using today's technologies, such as digital data, they announce the instantaneous measurement, and some other instruments also have a mechanical function, but they are designed and produced based on engineering principles. are Standard working conditions of filter regulator model PP3 The regulator filter can be used at a temperature of +40 to -5 degrees Celsius and with a fluid pressure of 10 to 0 bar. Note that if the incoming air is stained with oil or grease, the dehumidifier filter will be greased and unable to absorb moisture. Uses of PP3 model regulator filter: The reason for using filter regulators in the ventilation system is to separate moisture from the air, because if the air used contains moisture, it will cause irreparable problems, which we will mention a few of: 1. Rotting and loss of all O-rings and packings in the air steering jacks and valves and oxidation, rotting and rusting of the body of the air steering jacks and valves. 2. In the paint industry, we can mention the creation of water holes, the unevenness of the paint surface and many different problems. He pointed out in machine building, food, pharmaceutical, health, construction, oil, gas, petrochemical and other industries. Criteria for the regulator filter stone material: Filter material (brass filter-felt filter) Filter micronization (from forty microns to one hundredth of a micron) Appearance and dimensions of the filter Usually, filter stone (filter element) with 40 or 20 micron is used in the filter of existing regulators. 20 micron stone is used in felt filters. Definition of Prerequisite Care Unit Introduction of Filter Regulator The filter regulator is one of the parts used in the maintenance unit of pneumatic systems. In this article, the care unit is the same as the pneumatic care unit, and we intend to introduce one of the most important parts of this section, the regulator filter. Pneumatic systems are used in various industries and in industrial machines. Pneumatic systems, like their importance, are sensitive to different conditions, including polluted and humid air, and they must be supplied with healthy air in order to have proper efficiency, for this reason, different parts are used to create suitable conditions, which are a unit It is called care. The care unit is a set that aims to design Its essence is to create suitable conditions for the operation of the pneumatic system. This care unit includes parts such as regulator, filter regulator and oiler. Among the most important types of care units that are popular in the Iranian market, we can mention these brands: Metal work made in Italy Airtech SKP South Korea Festo Germany Aventics (Germany) Aignep (Italy) Shako Filter Regulator is the main topic of this article, and in the rest of this text, we intend to provide specialized information about the filter regulator, but since the Filter Regulator is related to other parts of a pneumatic care unit, at first, briefly We will introduce other components of this care unit, such as oiler and regulator. Introduction to the introduction of PP3 model regulator filter The PP3 model regulator filter is one of the parts that is used in the pneumatic system care unit along with the oiler. In the pneumatic systems care unit, different parts must work together so that the overall process of a project is done well. For this reason, the compactness of the work and the proximity of the parts can cause friction and locking of a part and disrupt the functioning of a set. In order to solve this problem and prevent disruptions in the work of the care unit as well as serious breakdowns of the devices, it is recommended that oil-consuming parts be lubricated in defined time intervals by a specialized device. To do this, the lubricant is used in the care unit. In fact, to inject oil into parts such as actuators and valves, the required oil is injected into the system's compressed air by the lubricator. The lubricating oil consists of different parts and by means of it the required amount of oil can be injected into the system. Different oils can be injected into a pneumatic system by using an oiler. Choosing the type of oil and its amount is an important and specialized issue that the experts of a project should decide on. Getting to know the regulator, introduction to the introduction of the regulator filter PP3 model regulator filter is one of the main parts of industrial regulators. And to get to know this piece, we need to get to know the regulator first. Regulator (in English regulator) is a word that is derived from the word regulate which means flow regulator. In other words, a regulator is a part that is used to control and adjust the input of a material to a system. These inputs can include vaporized liquids, gases, and even electrical voltages. In general, the regulator adjusts the flow to a system with a certain amount of pressure determined for it. Due to the fact that the input material to the regulators is different, and the systems in which the regulators are used are different and wide, as a result, various examples of the regulator have been produced, among which the following can be mentioned: Gas regulator Electric regulators Fluid regulators Filter Regulator The PP3 model gas or pneumatic regulator filter is a part that is mainly used for industrial and household regulators. In general, regulators are divided into two categories: household and industrial regulators, which are familiar to all of us and are parts that are used to adjust the gas pressure of cylinders and household gas in general, but in contrast to these small parts, professional industrial regulators are located Industrial regulators are usually produced for large tanks and high pressures. These regulators have special features according to the industry they are used in. For example, these regulators must be made of resistant materials and have resistance against gases, corrosive liquids, and sometimes toxic and putrid. Industrial regulators are equipped with various parts, one of the most important of which is the filter regulator PP3 model, which we will introduce in the rest of this text. Types of regulator filters PP3 model regulator filter is a small but very important industrial part that plays an effective role in performing various operations of a project. In fact, this part is considered a part of the monitoring unit of a system. Gas or pneumatic regulators are the most common types of regulators used in the industry. These regulators need an important part to apply standardization of intake air for proper and principled operation, and this important part is the regulator filter. The PP3 model regulator filter is a part that is necessary for the operation of the regulator. In fact, the air in the environment that we breathe contains some moisture. Humidity is the amount of heat present in a unit volume of air. Air enters pneumatic systems in a compressed form and this problem causes the accumulation of moisture in these systems, especially the bottom of the compressors, as a result of which decay and failure occur in these equipments. Filter Regulator is used to prevent this unpleasant event. The PP3 model regulator filter absorbs the moisture in an inlet and makes the system work better. Filter Regulator as an important part is made up of different parts. For example, the water in the inlet gas accumulates in the filter cup over time and is drained manually or automatically depending on the type of filter. A filter regulator is also used to prevent dust from entering a pneumatic system. In some areas as well as work environments, dust is part of the environmental conditions, for this reason, the work systems of a project are taken care of by this part. Filter Regulator Filter regulator model PP3 b As an important functional part in regulators, it is produced from various raw materials and has various sizes that should be selected and purchased based on the type of regulator. Regulator filter model PP3 Regulator filter model PP3 PP3 model regulator filter as an important part of an industrial regulator, and a part of the care unit of a system, can be classified in different ways. For example, this important part is produced from different raw materials, which must be resistant to different environmental conditions. Among these materials, we can mention brass metal as well as felt filters. As a result, the type of raw materials can be considered as a factor for the division of regulator filter types. The regulator filter is also produced in different sizes. Each size is used in certain systems and cases. The most important sizes of the PP3 filter regulator can be one inch, three-quarters of an inch, one-quarter of an inch, one-half of an inch, one-eighth of an inch, three-eighths of an inch, two inches, one and a half inches, and one and a quarter. Inch pointed. Of course, two-part sizes such as three-quarter inches are available in one piece and sizes such as one and a half inches are offered in two pieces due to their larger dimensions and are used in certain systems. The PP3 model regulator filter is a piece that absorbs the moisture in the compressed air and must be drained after reaching the set amount. The discharge of this part is done manually and automatically, and for this reason, the regulator filters are also produced in two types, automatic and manual. Filter Regulator PP3 model regulator filter is an industrial piece that is produced by various companies around the world today and each brand claims to produce quality products, for this reason, regulator filters can be divided into different categories based on the production brand. divided But in general, it is recommended to buy reliable and quality brands only through reliable sales centers. Important points on how to install PP3 model regulator filters PP3 model regulator filter is considered as one of the main and important parts of devices based on pneumatic systems, whose malfunction can cause irreparable damage to a project and its machines. This is one of the most important points that should be taken into account when buying the PP3 filter regulator. As a result, it is necessary to buy a quality and suitable piece. The PP3 model regulator filter is a part that is produced in different models and capacities, and for this reason, in the first step of buying a regulator filter, you should know your needs so that you can make a successful purchase based on your real and correct needs. . Since the regulator is produced in a variety of different models, it is necessary to purchase a suitable size filter for a regulator. Filter Regulator PP3 filter regulator is available in different types and brands with different prices. Naturally, most buyers tend to make their purchase with the best quality and the most suitable price. But the important thing is to buy regulator filters with a sales guarantee. Most of the big companies producing this part offer their products with a sales guarantee, it is recommended to pay attention to the warranty of the purchased product when buying. The filter regulator model PP3 is a part that is produced today by various companies around the world, and some of these brands produced by professional companies are well-known and popular, but in addition to the popular brands Filter Regulator, the filter regulator model PP3, There are also low-quality samples whose use can endanger the health of work and parts of a project. For this reason, it is recommended to visit reputable agencies to buy popular and well-known brands of industrial regulator filters. Today, due to the importance of this part in different industries, agencies of different brands have been set up in different provinces of Iran that offer quality products. Advantages of buying Filter Regulator from reputable dealers The PP3 model regulator filter is an important part that can be purchased in different ways in the market. Usually, industrial supply stores supply this part like other tools and parts in a normal way, and they do not accept any obligation against product failure or after-sales service, and this issue can be changed in the future. In case of possible failure of the part, it will be to the detriment of the buyers. For this reason, it is recommended to buy all kinds of regulator filters from reputable dealers. Among the most important advantages of buying this product from reputable dealers are the following: Buy the original products of each brand: To buy a specific brand of PP3 model regulator filter, you must visit the authorized dealers of the same brand. For example, some reputable and best-selling brands of filter regulator, PP3 model, have attracted the attention of profit-seeking collections in East Asian countries, and counterfeit samples from reputable brands have entered the market, which unfortunately look similar to the original samples, and that's why The reason is to avoid unknowingly buying fake products, it is recommended to buy from reputable dealers of the desired brand. Buy PP3 model regulator filter at a great price: PP3 model regulator filter is a product that has different prices in different stores, but to buy any brand at the best price, it is recommended to visit official dealers. Receiving after-sales service: The regulator filter is a part that must be installed Install it according to the defined standards. Usually, in the official agencies of different brands of PP3 regulator filter, there are people who can give you free advice and guidance to buy the right product and how to install it. | SQ model automatic fitting Pneumatic fittings are used to connect different parts of the pneumatic system, hoses and pipes. Pneumatic fittings are stronger and more resistant than hydraulic fittings. For this reason, while connecting parts in pneumatic systems, less pressure is applied to the connections and parts. Pneumatic connections or fittings are used to create a connection between the parts and components of a pneumatic system and circuit. For example, in a pneumatic system that includes a pneumatic valve, a pneumatic jack with speed control, various connections are used to connect these components to each other and to the compressed air of the main inlet. Pneumatic fittings are among the most widely used pneumatic devices that are used to connect and communicate between different components of pneumatic systems. By purchasing the pneumatic SQ model automatic fitting, you will see an increase in the speed of operation in the progress of pneumatic systems and works. Due to the fact that pneumatics are made up of different components, it is obvious that you will need to purchase several pneumatic fittings in different dimensions and features. Similarly, in building water piping, various connections such as elbows, bushings, spools, etc. are used to connect different components (such as pipes to each other, pipes to faucets, etc.). SQ pneumatic automatic fitting is made of various materials such as polymer and metal materials (iron with chrome coating and brass). SQ model automatic fitting application Pneumatic connectors are used to connect pneumatic components, and miniature connectors are used to change the inlet air pressure or change its direction. Pneumatic fittings are considered as precise tools in control. Air or pneumatic connections are one of the most important parts in the compressor. Without these parts, you cannot use the air effectively and even if the device is not installed correctly, the compressor may be damaged. We have included the best pneumatic (air) fittings in our product list for your review so that you can find the right part to meet your compressor needs. Having a reliable quick connect for air compressors is exactly the difference between a quality compressor and a serious hazard, and can help the consumer increase the compressor's air supply and possibly manage more complex connections. To optimize the life of your equipment, invest in buying high-quality and durable connections. These connections are the link between pipes, hoses and machines. Therefore, having a complete communication is essential for safety. This SQ model automatic fitting is very suitable for controlling air flow pressure and directional flow. SQ model automatic fitting components Pneumatic fittings may include parts such as pipes, tubes and hoses. Hose: Layers of different materials are used to make the hose. Hoses are highly flexible and provide suitable conditions for the movement of parts. Hoses need to be replaced after some time. It becomes necessary to replace the hose when it wears out. Pipe: Solid materials are used to make the pipe. These types of joints appear hard and rigid. tobacco pipe: Pipes are also made of solid materials and have significant hardness. Pipes are less flexible than pipes. The way the parts work and connect in the pneumatic system is different. In fact, this difference in appearance causes the automatic connection (fitting) of the mentioned SQ pneumatic model in various forms. L fittings Some of these connections are L-shaped or elbow. L joints are introduced as angle joints. The angle considered for L connections is 90 degrees. L-shaped pneumatic connections allow multi-purpose or single hoses to be connected. With a pneumatic elbow fitting, the connection of the system can be easily changed by means of a set of pipes. These types of connections are very compact and require little space. Pneumatic fitting is very useful and excellent for working with nylon pipes. Direct connections Pneumatic connections can be of direct type. In direct connections, one direction of the part is connected to the hose or pipe and the other direction is connected to other parts of the system. Bolts and nuts are used to fix these connections. The pneumatic direct fitting acts as an adapter. These fittings are available in different materials, thread sizes, diameters and grades. Direct pneumatic connections can be used with various tools. For this reason, direct connections are used a lot in the pneumatic system. T connection Pneumatic connections can be T-shaped. These connections are used with a pressure mechanism. T-shaped fittings are intended for safe and secure connection to threaded ports and support quick and easy installation without the need for tools. By establishing this connection, the parts can be placed side by side in a three-sided form. The most common application of T-shaped fittings is related to pressure or vacuum applications. The leakage of these T-shaped connections is very low and these connections are designed in the form of a complete hole. Y joints Y-shaped pneumatic joints can be used for various things such as air tools, textile, transportation applications, automotive, industrial airlines, garages, packaging, robotics, etc. Pneumatic Y-shaped connections are introduced with features such as fast disconnection and connection and tank strength against vacuum. Functional connections Pneumatic fittings can be divided according to the type of function. The body of the pneumatic fitting can be copper, aluminum, steel, PBT and Bern. Functional pneumatic fittings are used for functions such as shut-off, flow regulation, supply, exhaust and blocking. Communication connections Pneumatic fittings are also classified according to the type of connection. Ball joint Ball pneumatic fitting is used to connect the outer sleeve to the inner fitting. Sleeves are used to disconnect and connect two ends of connections. This type of connection is used for things that require frequent connection and disconnection of the hose. Compressor connection The connections mentioned can be compression or compressor type. In this type of connections, pressure is used to establish the connection. Rings, metal washers and ferrules are used for standard compression and connection. In such a case, the nut is used on the ferrule and pipe for compression. With this nut, it is possible to strengthen and compress the parts together. SQ model automatic fittings Pneumatic fittings are differentiated based on the type of connection and the function they perform. And they are produced in different sizes and types, each of which is used in different uses. Among these connections, we can mention the direct connection, which is available in direct allen-khor, panel direct, plastic bead direct, and direct connection between ways. One of the most widely used pneumatic parts are pneumatic tees. There are different types of tees, tees that feed hoses or tees with hose heads, tees in the middle of the rib and inside the thread, and miniature tees are of this category. The variety of pneumatic connections is very large. In general, connections can be divided into four main parts. 1- Connections with only connection function: This type of connections can be divided into the following two types: 1- Connections with one gear end and one hose end 2- Connections with two hose ends Connections with a gear end and a hose end It is used to connect pneumatic hoses to pneumatic valves or pneumatic manifolds. When buying this type of connection, you should pay attention to the size of the gear, the standard of the gear, the size of the connecting hose, the type of gear (male or female), whether or not it has O-rings, and the physical shape of the connection. SQ model automatic fitting Connections with two hose ends It is used to connect two pneumatic hoses to each other or change the connection size. For example, PUC-06 connector is used to connect two size 6 hoses. When buying this type of connection, we should pay attention to the size of the hose and the physical shape of the connection. 2- Connections with special functions: In addition to connecting two parts, this type of connections also have the following special functions. Types of flow controller: Flow controls are used to control flow rate or air flow. One of the important applications of flow control is controlling the movement speed of pneumatic jacks in the industry. Fluocontrollers are available in different types of flowcontrollers (with two hose feeding ends) and jackhead flowcontrollers (to connect to pneumatic jacks). SQ model automatic fitting. Stop fittings: In addition to the connection, these parts act as a one-way valve, and if the hose is placed in it, the air flow is established, and if the hose is removed, the air flow is automatically cut off. In using this connection, you should pay attention to its input and output. When buying, we should pay attention to the size of the hose and its thread. SQ model automatic fitting Check Valve: This type of connection is used to make the air path unidirectional. In using this connection, you should pay attention to its input and output. Also, when buying, you should pay attention to the size of the hose and its thread. It should be noted that the maximum working pressure of pneumatic connections is 10 bar, and if the pressure increases beyond this amount, there is a possibility of leakage and disconnection of the connection. SQ model automatic fitting 3- Connections for acidic substances and water: There are also connections that are completely made of plastic and are used for water and acidic things. SQ model automatic fitting 4- Couplings: Couplings are used to temporarily connect two parts of a system. For example, in gas pumps, the fuel nozzle is connected to a coupling, and when refueling, this nozzle is connected to the car's gas tank by the coupling, and after refueling, it is separated from the car. Couplings are available in various sizes and in the form of male and female threads, hose connectors, and you should pay attention to these items when buying. SQ model automatic fitting Special features of SQ model automatic fitting • The pneumatic fitting can withstand a working pressure of 24 bar according to the size of the design. • The ability to install and use pneumatic system connections is very convenient and easy. Therefore, this SQ model automatic fitting will be different from other systems. • The rib part of the fittings is made of brass and PBT material can be seen in their body part. • The metal parts of the connections are also plated with nickel or zinc. • NBR O-rings are used to prevent leakage of connections. • Connections of the pneumatic system are supplied in the form of three-way middle rib, swivel knee, straight, etc. This diversity in design causes diversity in the application of SQ model automatic fitting. • Various types of NPT, BSPT, METRIC and BSP are used for SQ model automatic fittings. Important cut when using SQ model automatic fitting After purchasing Etsa L (fittings) SQ pneumatic automatic model, when using these pneumatic parts, you should pay attention to a series of points and do not use pneumatic connections in the following conditions: 1- For other uses other than what that particular pneumatic connection was designed and made for. 2- Never touch the part of the automatic connection (fitting) of the SQ pneumatic model when they are under pressure. (Because this will cause the hose to separate and lead to damage). 3- In places where excessive external pressure is applied to the pneumatic connection due to stretching, bending or twisting (because it causes the body of the pneumatic connection to break and create dangerous situations). 4- In places where there is excessive vibration, rotation and bending. 5- In places where SQ pneumatic automatic fittings are exposed to corrosive, inflammable fluids, chemicals, sea water, or water vapor. Also, when buying pneumatic SQ model automatic fittings, you should note that these parts should not be used in machines that are used for purposes such as human life safety, human transportation, or emergency safety tools in general. Use SQ pneumatic automatic fittings only when all impurities such as dust have been removed from them. | DPSA model digital pressure switchDPSA model digital pressure switch works by combining the mechanical properties of compressed air and electricity. Pneumatic pressurizer is a device for controlling and adjusting pressure that is used in compressed air lines. The switch has the concept of changing the situation, which means that in case of any type of pressure change in the pressure system, the switch controls or secures the situation. This product is one of the precision instrument equipment. Pressure works in two normally open and normally close contacts. In the normally closed state, the contacts are closed in the normal state, when the pressure rises too much, the contacts open in order to reduce the pressure. In the normal open mode, the switch remains open until the pressure exceeds its limit, and the contacts close quickly as the pressure rises. To buy DPSA model digital pressure switch, you should pay attention to things like working pressure range, adjustable maximum pressure, connection size, etc. What is DPSA digital pressure switch or pressure switch? Pneumatic pressure switch or pressure switch is a pressure control switch and is used to adjust the pressure of tanks or prevent pressure increase in pressurized environments in the industry. DPSA model digital pressure switch or pressure controller has an electrical contact and when the pressure reaches At the set value, the contact is activated and an electrical signal is sent and the switch is closed. DPSA model digital pressure switch DPSA model digital pressure switch Also, pressure switches may be designed in such a way that they disconnect or connect the system when the pressure increases or decreases. DPSA model digital pressure switches play an important role in establishing safety and control in pressurized systems, also pressure switches have different types according to usage, working pressure and fluid. How DPSA model digital pressure switch works Normally, pressure switches have a diaphragm filled with air. When the air pressure inside the diaphragm changes, the diaphragm plate changes its shape and causes movement in the calibrated spring connected to it (spring calibration means the previous adjustment of the spring in The required size is the same as the range of the switch). The spring is pushed back by applying pressure and returns to its original position when the pressure is removed. This action is transferred to the electrical contact of the pressure switch and causes the operation of the pressure switch. The spring is set in different ranges for low or high pressures. Depending on the selected range, this spring opens or compresses. Depending on the type of fluid or gas that comes into contact with the diaphragm, the diaphragm has different types, such as: fibrous, plastic, Metal and.. DPSA model digital pressure switches Differential pressure switch Diaphragm switch pressure Capsule pressure switch Diaphragm switch pressure Bellows pressure switch Bardoni pressure switch Piston pressure switch Types of DPSA model digital pressure switch in terms of working fluid Pneumatic Hydraulic DPSA model digital pressure switch This type of pressure switch is an air pressure switch and is one of the simplest types of pressure switches and is mostly used in pneumatic systems or air compressors. Other applications of pneumatic pressure switches include the following: When taking water, it automatically controls the domestic water pump, taking into account the pressure in the pipes. This pressure switch automatically turns off the air compressor when the pressure reaches the set level in the air compressor tank. The pneumatic pressure switch is used to control the charge inside the battery cell. If the pressure in the cockpit becomes too low due to the increase in altitude, it will automatically turn on the warning light in the cockpit of the aircraft. This switch is used to count the traffic of vehicles on the streets and fuel stations using a tube filled with air placed on the floor of the street or work station. Hydraulic pressure switch These types of pressure switches have many uses in cars, for example to warn if the engine oil pressure falls below the safe level. Before the 1960s, pressure switches were used in the hydraulic brake circuit to control the power to the brake light. In newer cars, it uses a switch directly activated by the brake pedal. The types of high-pressure hydraulic switches are as follows: Steam pressure switch gas Explosion Proof Water We will explain it further. Steam switch pressure: Their function is with steam. Steam pressure switches must be able to withstand high temperature and humidity. Steam pressure switches are used to cool water, oil, air and hydrogen fluoride. These types of pressure switches are NC or NO, and when the pressure reaches the set values, the alarm is turned on. Gas switch pressure: In this type of pressure switch, sparking in the electrical part should be prevented as much as possible. Gas pressure switches are also used for flammable gases. Explosion-proof pressure switch: This type of pressure switch is used in cases where there is a risk of fire caused by sparks and flammable gas. The explosion-proof pressure switch enclosure is resistant to sparks and the penetration of environmental gases. Water switch pressure: This type of pressure switch is used in hydraulic industries such as automobiles to display a warning when the engine oil pressure is lower than the acceptable level or to control the automatic locking of the automatic transmission torque. Also, these pressure switches are widely used in water pumps and water supply lines. | SP4000 large body metal flow control Pneumatic fittings are used to connect different parts of the pneumatic system, hoses and pipes. Pneumatic fittings are stronger and more resistant than hydraulic fittings. For this reason, while connecting parts in pneumatic systems, less pressure is applied to the connections and parts. Pneumatic connections or fittings are used to create a connection between the parts and components of a pneumatic system and circuit. For example, in a pneumatic system that includes a pneumatic valve, a pneumatic jack with speed control, various connections are used to connect these components to each other and to the compressed air of the main inlet. Pneumatic fittings are among the most widely used pneumatic devices that are used to connect and communicate between different components of pneumatic systems. With the purchase of SP4000 model SP4000 pneumatic flow control, you will see an increase in the speed of operation in the progress of works and pneumatic systems. Due to the fact that pneumatics are made up of different components, it is obvious that you will need to purchase several pneumatic fittings in different dimensions and features. Similarly, in building water piping, various connections such as elbows, bushings, spools, etc. are used to connect different components (such as pipes to each other, pipes to faucets, etc.). SP4000 pneumatic large body metal flow control is made of various materials such as polymer and metal materials (chrome coated iron and brass). The application of SP4000 large body metal flow control Pneumatic connectors are used to connect pneumatic components, and miniature connectors are used to change the inlet air pressure or change its direction. Pneumatic fittings are considered as precise tools in control. Air or pneumatic connections are one of the most important parts in the compressor. Without these parts, you cannot use the air effectively and even if the device is not installed correctly, the compressor may be damaged. We have included the best pneumatic (air) fittings in our product list for your review so that you can find the right part to meet your compressor needs. Having a reliable quick connect for air compressors is exactly the difference between a quality compressor and a serious hazard, and can help the consumer increase the compressor's air supply and possibly manage more complex connections. To optimize the life of your equipment, invest in buying high-quality and durable connections. These connections are the link between pipes, hoses and machines. Therefore, having a complete communication is essential for safety. This SP4000 large body metal flow control is very suitable for controlling air flow pressure and directional flow. SP4000 large body metal intermediate flow control components Pneumatic fittings may include parts such as pipes, tubes and hoses. Hose: Layers of different materials are used to make the hose. Hoses are highly flexible and provide suitable conditions for the movement of parts. Hoses need to be replaced after some time. It becomes necessary to replace the hose when it wears out. Pipe: Solid materials are used to make the pipe. These types of joints appear hard and rigid. tobacco pipe: Pipes are also made of solid materials and have significant hardness. Pipes are less flexible than pipes. The way the parts work and connect in the pneumatic system is different. In fact, this difference in appearance causes the existence of the above-mentioned SP4000 large body metal flow control in various forms. L fittings Some of these connections are L-shaped or elbow. L joints are introduced as angle joints. The angle considered for L connections is 90 degrees. L-shaped pneumatic connections allow multi-purpose or single hoses to be connected. With a pneumatic elbow fitting, the connection of the system can be easily changed by means of a set of pipes. These types of connections are very compact and require little space. Pneumatic fitting is very useful and excellent for working with nylon pipes. Direct connections Pneumatic connections can be of direct type. In direct connections, one direction of the part is connected to the hose or pipe and the other direction is connected to other parts of the system. Bolts and nuts are used to fix these connections. The pneumatic direct fitting acts as an adapter. These fittings are available in different materials, thread sizes, diameters and grades. Direct pneumatic connections can be used with various tools. For this reason, direct connections are used a lot in the pneumatic system. T connection Pneumatic connections can be T-shaped. These connections are used with a pressure mechanism. T-shaped fittings are intended for safe and secure connection to threaded ports and support quick and easy installation without the need for tools. By establishing this connection, the parts can be placed side by side in a three-sided form. The most common application of T-shaped fittings is related to pressure or vacuum applications. The leakage of these T-shaped connections is very low and these connections are designed in the form of a complete hole. Y joints Y-shaped pneumatic joints can be used for various things such as air tools, textile, transportation applications, automotive, industrial airlines, garages, packaging, robotics, etc. Pneumatic Y-shaped connectors with features such as disconnecting and connecting the head | Silencer (BC sintered) SNBMuffler (exhaust) SNB model Pneumatic fittings are used to connect different parts of the pneumatic system, hoses and pipes. Pneumatic fittings are stronger and more resistant than hydraulic fittings. For this reason, while connecting parts in pneumatic systems, less pressure is applied to the connections and parts. Pneumatic connections or fittings are used to create a connection between the parts and components of a pneumatic system and circuit. For example, in a pneumatic system that includes a pneumatic valve, a pneumatic jack with speed control, various connections are used to connect these components to each other and to the compressed air of the main inlet. Pneumatic fittings are among the most widely used pneumatic devices that are used to connect and communicate between different components of pneumatic systems. By purchasing the silencer (exhaust) of the SNB pneumatic model, you will see an increase in the speed of operation in the progress of pneumatic systems and works. Due to the fact that pneumatics are made up of different components, it is obvious that you will need to purchase several pneumatic fittings in different dimensions and features. Similarly, in building water piping, various connections such as elbows, bushings, spools, etc. are used to connect different components (such as pipes to each other, pipes to faucets, etc.). Muffler (exhaust) pneumatic SNB model is made of different materials such as polymer and metal materials (iron with chrome coating and brass). Application of muffler (exhaust) model SNB Pneumatic connectors are used to connect pneumatic components, and miniature connectors are used to change the inlet air pressure or change its direction. Pneumatic fittings are considered as precise tools in control. Air or pneumatic connections are one of the most important parts in the compressor. Without these parts, you cannot use the air effectively and even if the device is not installed correctly, the compressor may be damaged. We have included the best pneumatic (air) fittings in our product list for your review so that you can find the right part to meet your compressor needs. Having a reliable quick connect for air compressors is exactly the difference between a quality compressor and a serious hazard, and can help the consumer increase the compressor's air supply and possibly manage more complex connections. To optimize the life of your equipment, invest in buying high-quality and durable connections. Muffler (exhaust) SNB model Muffler (exhaust) SNB model These connections are the link between pipes, hoses and machines. Therefore, having a complete communication is essential for safety. This muffler (exhaust) model SNB is very suitable for controlling air flow pressure and directional flow. Muffler components (exhaust) SNB model Pneumatic fittings may include parts such as pipes, tubes and hoses. Hose: Layers of different materials are used to make the hose. Hoses are highly flexible and provide suitable conditions for the movement of parts. Hoses need to be replaced after some time. It becomes necessary to replace the hose when it wears out. Pipe: Solid materials are used to make the pipe. These types of joints appear hard and rigid. tobacco pipe: Pipes are also made of solid materials and have significant hardness. Pipes are less flexible than pipes. The way the parts work and connect in the pneumatic system is different. In fact, this difference in appearance causes the silencer (exhaust) of the aforementioned pneumatic SNB model to appear in various forms. L fittings Some of these connections are L-shaped or elbow. L joints are introduced as angle joints. The angle considered for L connections is 90 degrees. L-shaped pneumatic connections allow multi-purpose or single hoses to be connected. With a pneumatic elbow fitting, the connection of the system can be easily changed by means of a set of pipes. These types of connections are very compact and require little space. Pneumatic fitting is very useful and excellent for working with nylon pipes. Direct connections Pneumatic connections can be of direct type. In direct connections, one direction of the part is connected to the hose or pipe and the other direction is connected to other parts of the system. Bolts and nuts are used to fix these connections. The pneumatic direct fitting acts as an adapter. These fittings are available in different materials, thread sizes, diameters and grades. Direct pneumatic connections can be used with various tools. For this reason, direct connections are used a lot in the pneumatic system. T connection Pneumatic connections can be T-shaped. These connections are used with a pressure mechanism. T-shaped fittings are intended for safe and secure connection to threaded ports and support quick and easy installation without the need for tools. By establishing this connection, the parts can be placed side by side in a three-sided form. The most common application of T-shaped fittings is related to pressure or vacuum applications. The leakage of these T-shaped connections is very low and these connections are designed in the form of a complete hole. Y joints Y-shaped pneumatic joints can be used for various things such as air tools, textile, transportation applications, automotive, industrial airlines, garages, packaging, robotics, etc. Pneumatic Y-shaped connections are introduced with features such as fast disconnection and connection and tank strength against vacuum. and strength of the tank against vacuum are introduced. Functional connections Pneumatic fittings can be divided according to the type of function. The body of the pneumatic fitting can be copper, aluminum, steel, PBT and Bern. Functional pneumatic fittings are used for functions such as shut-off, flow regulation, supply, exhaust and blocking. Communication connections Pneumatic fittings are also classified according to the type of connection. Ball joint Ball pneumatic fitting is used to connect the outer sleeve to the inner fitting. Sleeves are used to disconnect and connect two ends of connections. This type of connection is used for things that require frequent connection and disconnection of the hose. Compressor connection The connections mentioned can be compression or compressor type. In this type of connections, pressure is used to establish the connection. Rings, metal washers and ferrules are used for standard compression and connection. In such a case, the nut is used on the ferrule and pipe for compression. With this nut, it is possible to strengthen and compress the parts together. SP4000 metal flow control with large body Pneumatic fittings are differentiated based on the type of connection and the function they perform. And they are produced in different sizes and types, each of which is used in different uses. Among these connections, we can mention the direct connection, which is available in direct allen-khor, panel direct, plastic bead direct, and direct connection between ways. One of the most widely used pneumatic parts are pneumatic tees. There are different types of tees, tees that feed hoses or tees with hose heads, tees in the middle of the rib and inside the thread, and miniature tees are of this category. The variety of pneumatic connections is very large. In general, connections can be divided into four main parts. 1- Connections with only connection function: This type of connections can be divided into the following two types: 1- Connections with one gear end and one hose end 2- Connections with two hose ends Connections with a gear end and a hose end It is used to connect pneumatic hoses to pneumatic valves or pneumatic manifolds. When buying this type of connection, you should pay attention to the gear size, gear standard, connecting hose size, type of gear (male or female), whether or not it has O-rings, and the physical shape of the connection. SP4000 large body metal flow control Connections with two hose ends It is used to connect two pneumatic hoses to each other or change the connection size. For example, PUC-06 connector is used to connect two size 6 hoses. When buying this type of connection, we should pay attention to the size of the hose and the physical shape of the connection. 2- Connections with special functions: In addition to connecting two parts, this type of connections also have the following special functions. Types of flow controller: Flow controls are used to control flow rate or air flow. One of the important applications of flow control is controlling the movement speed of pneumatic jacks in the industry. Fluocontrollers are available in different types of fluocontrollers (two hose feeding ends) and jack-head fluocontrollers (to connect to pneumatic jacks). SP4000 large body metal flow control Stop fittings: In addition to the connection, these parts act as a one-way valve, and if the hose is placed in it, the air flow is established, and if the hose is removed, the air flow is automatically cut off. In using this connection, you should pay attention to its input and output. When buying, we should pay attention to the size of the hose and its thread. SP4000 large body metal flow control Check Valve: This type of connection is used to make the air path unidirectional. In using this connection, you should pay attention to its input and output. Also, when buying, you should pay attention to the size of the hose and its thread. It should be noted that the maximum working pressure of pneumatic connections is 10 bar, and if the pressure increases more than this value, there is a possibility of leakage and disconnection of the connection. SP4000 large body metal flow control 3- Connections for acidic substances and water: There are also connections, they are completely made of plastic and are used for water and acidic cases. SP4000 large body metallic flow control. 4- Couplings: Couplings are used to temporarily connect two parts of a system. For example, in gas pumps, the fuel nozzle is connected to a coupling, and when refueling, this nozzle is connected to the car's gas tank by the coupling, and after refueling, it is separated from the car. Couplings are available in various sizes and in the form of male and female threads, hose connectors, and you should pay attention to these items when purchasing. SP4000 large body metal flow control. Special features of SP4000 large body metal flow control • The pneumatic fitting can withstand a working pressure of 24 bar according to the size of the design. • The ability to install and use pneumatic system connections is very convenient and easy. For this reason, this SP4000 large-body metal flow control system will be different from other systems. • The rib part of the fittings is made of brass and PBT material can be seen in their body part. • The metal parts of the connections are also plated with nickel or zinc. • NBR O-rings are used to prevent leakage of connections. • Connections of the pneumatic system are supplied in the form of three-way middle rib, swivel knee, straight, etc. This diversity in design causes diversity in the application of flow control in the way The large body of the SP4000 model is also made of metal. • Various types such as NPT, BSPT, METRIC and BSP are used for SP4000 large body metal flow control gears. Important cut when using SP4000 pneumatic large body metal flow control After purchasing the large SP4000 model pneumatic flow control, when using these pneumatic parts, you should pay attention to a series of points and do not use the pneumatic connections in the following conditions: 1- For other uses other than what that particular pneumatic connection was designed and made for. 2- Never touch the release part of the SP4000 pneumatic large body metal flow control when they are under pressure. (Because this will cause the hose to separate and lead to damage). 3- In places where excessive external pressure is applied to the pneumatic connection due to stretching, bending or twisting (because it causes the body of the pneumatic connection to break and create dangerous situations). 4- In places where there is excessive vibration, rotation and bending. 5- In places where SP4000 large body metal pneumatic flow control is exposed to corrosive, inflammable fluid, chemicals, sea water or water vapor. Also, when buying a large-body metal SP4000 pneumatic flow control, you should note that these parts should not be used in machines that are used for purposes such as human life safety, human transportation, or emergency safety tools in general. Use SP4000 pneumatic large body metal flow control only when all impurities such as dust have been removed from them. | |||||||||||||
| Weight | n. v. | n. v. | n. v. | n. v. | n. v. | n. v. | ||||||||||||
| Dimensions | n. v. | n. v. | n. v. | n. v. | n. v. | n. v. | ||||||||||||
| Additional information |
|
|
|
|
|
|
Related products
- Liquid compressed air, maximum working pressure (MPa) 1.0MPa (10.2kgf/cm2)
- Noise reduction of 20dB(A) and above
- Ambient and fluid temperature (℃) -5 to 60 (without freezing)
liquid air
Maximum operating pressure (MPa) 1.0 (140psi)
Constant pressure (MPa) 1.5 (200psi)
Standard pressure setting 0.05~1.0 (7~140psi)
(MPa) Customized specifications 0.05~0.2 (7~30psi), 0.05~0.4 (7~60psi), 0.05~1.5 (7~200psi)
Ambient and fluid temperature (℃) -5 ~ 60 (23 ~ 140 °F) (non-freezing)
Flow capacity ※ 3/8 ˝ 3,800 (134scfm)
(Nℓ/min) 1/2˝ 4700 (166scfm)
Filtration (㎛) 5
Soothing style of construction
Polycarbonate bowl material
Nylon bowl protective material
Discharge Capacity (㎤) Manual Drain: 56 (1.89 oz), Auto Discharge: 68 (2.3 oz)
Weight (kg) 0.74 (1.63 lbs)
● ONE ACTION inserts tube for easy attachment and release
● The volume and OD are smaller than the conventional type, but the same flux is obtained
● Surface treated with electroless nickel plating for excellent corrosion resistance
● The oval sleeve is designed to be easily released in confined spaces
● The screw part has O-rings or has a sealant coating
● Small fittings for small appliances and piping in confined spaces
- Liquid compressed air, maximum working pressure (MPa) 1.0MPa (10.2kgf/cm2)
- Noise reduction of 20dB(A) and above
- Ambient and fluid temperature (℃) -5 to 60 (without freezing)
● ONE ACTION inserts tube for easy attachment and release
● The volume and OD are smaller than the conventional type, but the same flux is obtained
● Surface treated with electroless nickel plating for excellent corrosion resistance
● The oval sleeve is designed to be easily released in confined spaces
● The screw part has O-rings or has a sealant coating
● Small fittings for small appliances and piping in confined spaces
Bewertungen
Es gibt noch keine Bewertungen.