No products in the cart.
SP4000 large body metal flow control
● The holder prevents accidental loss of the needle
● Compact size saves space
● Speed must be carefully controlled even at low speed
● Lock nut
● Copper free type for electronics industry (optional)
● Compact size saves space
● Speed must be carefully controlled even at low speed
● Lock nut
● Copper free type for electronics industry (optional)
Zur Wunschliste hinzufügen
Zur Wunschliste hinzufügen
Categories: brand, Large body metal flow control, Pneumatic, Pneumatic fittings, TPC, TPC fittings
Marke: TPC
Beschreibung
SP4000 large body metal flow control
Pneumatic fittings are used to connect different parts of the pneumatic system, hoses and pipes. Pneumatic fittings are stronger and more resistant than hydraulic fittings. For this reason, while connecting parts in pneumatic systems, less pressure is applied to the connections and parts.
Pneumatic connections or fittings are used to create a connection between the parts and components of a pneumatic system and circuit. For example, in a pneumatic system that includes a pneumatic valve, a pneumatic jack with speed control, various connections are used to connect these components to each other and to the compressed air of the main inlet.
Pneumatic fittings are among the most widely used pneumatic devices that are used to connect and communicate between different components of pneumatic systems. With the purchase of SP4000 model SP4000 pneumatic flow control, you will see an increase in the speed of operation in the progress of works and pneumatic systems. Due to the fact that pneumatics are made up of different components, it is obvious that you will need to purchase several pneumatic fittings in different dimensions and features.
Similarly, in building water piping, various connections such as elbows, bushings, spools, etc. are used to connect different components (such as pipes to each other, pipes to faucets, etc.). SP4000 pneumatic large body metal flow control is made of various materials such as polymer and metal materials (chrome coated iron and brass).
The application of SP4000 large body metal flow control
Pneumatic connectors are used to connect pneumatic components, and miniature connectors are used to change the inlet air pressure or change its direction. Pneumatic fittings are considered as precise tools in control.
Air or pneumatic connections are one of the most important parts in the compressor. Without these parts, you cannot use the air effectively and even if the device is not installed correctly, the compressor may be damaged. We have included the best pneumatic (air) fittings in our product list for your review so that you can find the right part to meet your compressor needs.
Having a reliable quick connect for air compressors is exactly the difference between a quality compressor and a serious hazard, and can help the consumer increase the compressor’s air supply and possibly manage more complex connections. To optimize the life of your equipment, invest in buying high-quality and durable connections.
These connections are the link between pipes, hoses and machines. Therefore, having a complete communication is essential for safety. This SP4000 large body metal flow control is very suitable for controlling air flow pressure and directional flow.
SP4000 large body metal intermediate flow control components
Pneumatic fittings may include parts such as pipes, tubes and hoses.
Hose:
Layers of different materials are used to make the hose. Hoses are highly flexible and provide suitable conditions for the movement of parts. Hoses need to be replaced after some time. It becomes necessary to replace the hose when it wears out.
Pipe:
Solid materials are used to make the pipe. These types of joints appear hard and rigid.
tobacco pipe:
Pipes are also made of solid materials and have significant hardness. Pipes are less flexible than pipes.
The way the parts work and connect in the pneumatic system is different. In fact, this difference in appearance causes the existence of the above-mentioned SP4000 large body metal flow control in various forms.
L fittings
Some of these connections are L-shaped or elbow. L joints are introduced as angle joints. The angle considered for L connections is 90 degrees. L-shaped pneumatic connections allow multi-purpose or single hoses to be connected. With a pneumatic elbow fitting, the connection of the system can be easily changed by means of a set of pipes.
These types of connections are very compact and require little space. Pneumatic fitting is very useful and excellent for working with nylon pipes.
Direct connections
Pneumatic connections can be of direct type. In direct connections, one direction of the part is connected to the hose or pipe and the other direction is connected to other parts of the system. Bolts and nuts are used to fix these connections. The pneumatic direct fitting acts as an adapter.
These fittings are available in different materials, thread sizes, diameters and grades. Direct pneumatic connections can be used with various tools. For this reason, direct connections are used a lot in the pneumatic system.
T connection
Pneumatic connections can be T-shaped. These connections are used with a pressure mechanism. T-shaped fittings are intended for safe and secure connection to threaded ports and support quick and easy installation without the need for tools. By establishing this connection, the parts can be placed side by side in a three-sided form.
The most common application of T-shaped fittings is related to pressure or vacuum applications. The leakage of these T-shaped connections is very low and these connections are designed in the form of a complete hole.
Y joints
Y-shaped pneumatic joints can be used for various things such as air tools, textile, transportation applications, automotive, industrial airlines, garages, packaging, robotics, etc. Pneumatic Y-shaped connectors with features such as disconnecting and connecting the head
[caption id="attachment_5203" align="aligncenter" width="1456"]
فلوکنترل بین راهی فلزی بدنه بزرگ مدل SP4000[/caption]
Zusätzliche Informationen
| برند ها |
|---|
Quick Comparison
| Settings | SP4000 large body metal flow control remove | SPSA model digital pressure switch remove | Silencer (BC sintered) SNB remove | Flow control valve with SPC model lock remove | DPSA model digital pressure switch remove | Regulator filter model PP4 remove | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Name | SP4000 large body metal flow control remove | SPSA model digital pressure switch remove | Silencer (BC sintered) SNB remove | Flow control valve with SPC model lock remove | DPSA model digital pressure switch remove | Regulator filter model PP4 remove | ||||||||||||
| Image | |  |  |  |  |  | ||||||||||||
| SKU | ||||||||||||||||||
| Rating | ||||||||||||||||||
| Price | ||||||||||||||||||
| Stock | ||||||||||||||||||
| Availability | ||||||||||||||||||
| Add to cart | ||||||||||||||||||
| Description | ● The holder prevents accidental loss of the needle
● Compact size saves space
● Speed must be carefully controlled even at low speed
● Lock nut
● Copper free type for electronics industry (optional)
|
● High precision semiconductor pressure sensor
● Red LED with high brightness (number: 9.5 mm)
● Convertable pressure unit
● Different output modes
● Preventive function of output
● Analog output (1-5VDC)
● Current protection circuit, reverse polarity protection circuit
|
|
|
▪ Digital pressure sensor with high accuracy
▪ LCD screen with high brightness.
▪ High resolution: 1/1000 ▪ Convertable pressure unit - Combination pressure: kPa, kgf/cm2, bar, psi, mmHg, mmH2O, inHg - Standard pressure: kPa, kgf/cm2, bar, psi, Mpa
▪ Different output modes: Hysteresis mode, One point selting mode. 2 independent output mode, comparative window output mode
▪ Prevent chatter for output (selectable response time: 2.5, 5, 100, 500 milliseconds)
▪ Analog output scale function (1-5VDC).
▪ Reverse polarity protection circuit and excess current
▪ Zero point setting function ▪ Display peak and hold low
| liquid air Maximum operating pressure (MPa) 1.0 (140psi) Constant pressure (MPa) 1.5 (200psi) Standard pressure setting 0.05~1.0 (7~140psi) (MPa) Customized specifications 0.05~0.2 (7~30psi), 0.05~0.4 (7~60psi), 0.05~1.5 (7~200psi) Ambient and fluid temperature (℃) -5 ~ 60 (23 ~ 140 °F) (non-freezing) Flow capacity ※ 3/8 ˝ 3,800 (134scfm) (Nℓ/min) 1/2˝ 4700 (166scfm) Filtration (㎛) 5 Soothing style of construction Polycarbonate bowl material Nylon bowl protective material Discharge Capacity (㎤) Manual Drain: 56 (1.89 oz), Auto Discharge: 68 (2.3 oz) Weight (kg) 0.74 (1.63 lbs) | ||||||||||||
| Content | SP4000 large body metal flow control Pneumatic fittings are used to connect different parts of the pneumatic system, hoses and pipes. Pneumatic fittings are stronger and more resistant than hydraulic fittings. For this reason, while connecting parts in pneumatic systems, less pressure is applied to the connections and parts. Pneumatic connections or fittings are used to create a connection between the parts and components of a pneumatic system and circuit. For example, in a pneumatic system that includes a pneumatic valve, a pneumatic jack with speed control, various connections are used to connect these components to each other and to the compressed air of the main inlet. Pneumatic fittings are among the most widely used pneumatic devices that are used to connect and communicate between different components of pneumatic systems. With the purchase of SP4000 model SP4000 pneumatic flow control, you will see an increase in the speed of operation in the progress of works and pneumatic systems. Due to the fact that pneumatics are made up of different components, it is obvious that you will need to purchase several pneumatic fittings in different dimensions and features. Similarly, in building water piping, various connections such as elbows, bushings, spools, etc. are used to connect different components (such as pipes to each other, pipes to faucets, etc.). SP4000 pneumatic large body metal flow control is made of various materials such as polymer and metal materials (chrome coated iron and brass). The application of SP4000 large body metal flow control Pneumatic connectors are used to connect pneumatic components, and miniature connectors are used to change the inlet air pressure or change its direction. Pneumatic fittings are considered as precise tools in control. Air or pneumatic connections are one of the most important parts in the compressor. Without these parts, you cannot use the air effectively and even if the device is not installed correctly, the compressor may be damaged. We have included the best pneumatic (air) fittings in our product list for your review so that you can find the right part to meet your compressor needs. Having a reliable quick connect for air compressors is exactly the difference between a quality compressor and a serious hazard, and can help the consumer increase the compressor's air supply and possibly manage more complex connections. To optimize the life of your equipment, invest in buying high-quality and durable connections. These connections are the link between pipes, hoses and machines. Therefore, having a complete communication is essential for safety. This SP4000 large body metal flow control is very suitable for controlling air flow pressure and directional flow. SP4000 large body metal intermediate flow control components Pneumatic fittings may include parts such as pipes, tubes and hoses. Hose: Layers of different materials are used to make the hose. Hoses are highly flexible and provide suitable conditions for the movement of parts. Hoses need to be replaced after some time. It becomes necessary to replace the hose when it wears out. Pipe: Solid materials are used to make the pipe. These types of joints appear hard and rigid. tobacco pipe: Pipes are also made of solid materials and have significant hardness. Pipes are less flexible than pipes. The way the parts work and connect in the pneumatic system is different. In fact, this difference in appearance causes the existence of the above-mentioned SP4000 large body metal flow control in various forms. L fittings Some of these connections are L-shaped or elbow. L joints are introduced as angle joints. The angle considered for L connections is 90 degrees. L-shaped pneumatic connections allow multi-purpose or single hoses to be connected. With a pneumatic elbow fitting, the connection of the system can be easily changed by means of a set of pipes. These types of connections are very compact and require little space. Pneumatic fitting is very useful and excellent for working with nylon pipes. Direct connections Pneumatic connections can be of direct type. In direct connections, one direction of the part is connected to the hose or pipe and the other direction is connected to other parts of the system. Bolts and nuts are used to fix these connections. The pneumatic direct fitting acts as an adapter. These fittings are available in different materials, thread sizes, diameters and grades. Direct pneumatic connections can be used with various tools. For this reason, direct connections are used a lot in the pneumatic system. T connection Pneumatic connections can be T-shaped. These connections are used with a pressure mechanism. T-shaped fittings are intended for safe and secure connection to threaded ports and support quick and easy installation without the need for tools. By establishing this connection, the parts can be placed side by side in a three-sided form. The most common application of T-shaped fittings is related to pressure or vacuum applications. The leakage of these T-shaped connections is very low and these connections are designed in the form of a complete hole. Y joints Y-shaped pneumatic joints can be used for various things such as air tools, textile, transportation applications, automotive, industrial airlines, garages, packaging, robotics, etc. Pneumatic Y-shaped connectors with features such as disconnecting and connecting the head | SPSA model digital pressure switch The SPSA digital switch pressure switch works by combining the mechanical properties of compressed air and electricity. Pneumatic pressurizer is a device for controlling and adjusting pressure that is used in compressed air lines. The switch has the concept of changing the situation, which means that in case of any type of pressure change in the pressure system, the switch controls or secures the situation. This product is one of the precision instrument equipment. Pressure works in two normally open and normally close contacts. In the normally closed state, the contacts are closed in the normal state, when the pressure rises too much, the contacts open in order to reduce the pressure. In the normal open mode, the switch remains open until the pressure exceeds its limit, and the contacts close quickly as the pressure rises. To buy SPSA model digital pressure switch, you should pay attention to things like working pressure range, adjustable maximum pressure, connection size, etc. What is SPSA digital pressure switch or pressure switch? Pneumatic pressure switch or pressure switch is a pressure control switch and is used to adjust the pressure of tanks or prevent pressure increase in pressurized environments in the industry. SPSA model digital pressure switch or pressure controller has an electrical contact and when the pressure reaches the set value, the contact is activated and an electrical signal is sent and the switch is cut off. SPSA model digital pressure switch SPSA model digital pressure switch Also, pressure switches may be designed in such a way that they disconnect or connect the system when the pressure increases or decreases. SPSA model digital pressure switches play an important role in establishing safety and control in pressurized systems, also pressure switches have different types according to usage, working pressure and fluid. How SPSA model digital pressure switch works Normally, pressure switches have a diaphragm filled with air. When the air pressure inside the diaphragm changes, the diaphragm plate changes its shape and causes movement in the calibrated spring connected to it (spring calibration means the previous adjustment of the spring in The required size is the same as the range of the switch). The spring is pushed back by applying pressure and returns to its original position when the pressure is removed. This action is transferred to the electrical contact of the pressure switch and causes the operation of the pressure switch. The spring is set in different ranges for low or high pressures. Depending on the selected range, this spring opens or compresses. Depending on the type of fluid or gas that comes into contact with the diaphragm, the diaphragm has different types, such as: fibrous, plastic, Metal and.. SPSA model digital pressure switches Differential pressure switch Diaphragm switch pressure Capsule pressure switch Diaphragm switch pressure Bellows pressure switch Bardoni pressure switch Piston pressure switch SPSA model digital pressure switch in terms of working fluid Pneumatic Hydraulic SPSA model digital pressure switch This type of pressure switch is an air pressure switch and is one of the simplest types of pressure switches and is mostly used in pneumatic systems or air compressors. Other applications of pneumatic pressure switches include the following: When taking water, it automatically controls the domestic water pump, taking into account the pressure in the pipes. This pressure switch automatically turns off the air compressor when the pressure reaches the set level in the air compressor tank. The pneumatic pressure switch is used to control the charge inside the battery cell. If the pressure in the cockpit becomes too low due to the increase in altitude, it will automatically turn on the warning light in the cockpit of the aircraft. This switch is used to count the traffic of vehicles on the streets and fuel stations using a tube filled with air placed on the floor of the street or work station. Hydraulic pressure switch These types of pressure switches have many uses in cars, for example to warn if the engine oil pressure falls below the safe level. Before the 1960s, pressure switches were used in the hydraulic brake circuit to control the power to the brake light. In newer cars, it uses a switch directly activated by the brake pedal. The types of high-pressure hydraulic switches are as follows: Steam pressure switch gas Explosion Proof Water We will explain it further. Steam switch pressure: Their function is with steam. Steam pressure switches must be able to withstand high temperature and humidity. Steam pressure switches are used to cool water, oil, air and hydrogen fluoride. These types of pressure switches are NC or NO, and when the pressure reaches the set values, the alarm is turned on. Gas switch pressure: In this type of pressure switch, sparking in the electrical part should be prevented as much as possible. Gas pressure switches are also used for flammable gases. Explosion-proof pressure switch: This type of pressure switch is used in cases where there is a risk of fire caused by sparks and flammable gas. The explosion-proof pressure switch enclosure is resistant to sparks and the penetration of environmental gases. Water switch pressure: This type of pressure switch is used in hydraulic industries such as automobiles to display a warning when the engine oil pressure is lower than the acceptable level or to control the automatic locking of the automatic transmission torque. Also, these pressure switches are widely used in water pumps and water supply lines. | Silencer (BC sintered) SNBMuffler (exhaust) SNB model Pneumatic fittings are used to connect different parts of the pneumatic system, hoses and pipes. Pneumatic fittings are stronger and more resistant than hydraulic fittings. For this reason, while connecting parts in pneumatic systems, less pressure is applied to the connections and parts. Pneumatic connections or fittings are used to create a connection between the parts and components of a pneumatic system and circuit. For example, in a pneumatic system that includes a pneumatic valve, a pneumatic jack with speed control, various connections are used to connect these components to each other and to the compressed air of the main inlet. Pneumatic fittings are among the most widely used pneumatic devices that are used to connect and communicate between different components of pneumatic systems. By purchasing the silencer (exhaust) of the SNB pneumatic model, you will see an increase in the speed of operation in the progress of pneumatic systems and works. Due to the fact that pneumatics are made up of different components, it is obvious that you will need to purchase several pneumatic fittings in different dimensions and features. Similarly, in building water piping, various connections such as elbows, bushings, spools, etc. are used to connect different components (such as pipes to each other, pipes to faucets, etc.). Muffler (exhaust) pneumatic SNB model is made of different materials such as polymer and metal materials (iron with chrome coating and brass). Application of muffler (exhaust) model SNB Pneumatic connectors are used to connect pneumatic components, and miniature connectors are used to change the inlet air pressure or change its direction. Pneumatic fittings are considered as precise tools in control. Air or pneumatic connections are one of the most important parts in the compressor. Without these parts, you cannot use the air effectively and even if the device is not installed correctly, the compressor may be damaged. We have included the best pneumatic (air) fittings in our product list for your review so that you can find the right part to meet your compressor needs. Having a reliable quick connect for air compressors is exactly the difference between a quality compressor and a serious hazard, and can help the consumer increase the compressor's air supply and possibly manage more complex connections. To optimize the life of your equipment, invest in buying high-quality and durable connections. Muffler (exhaust) SNB model Muffler (exhaust) SNB model These connections are the link between pipes, hoses and machines. Therefore, having a complete communication is essential for safety. This muffler (exhaust) model SNB is very suitable for controlling air flow pressure and directional flow. Muffler components (exhaust) SNB model Pneumatic fittings may include parts such as pipes, tubes and hoses. Hose: Layers of different materials are used to make the hose. Hoses are highly flexible and provide suitable conditions for the movement of parts. Hoses need to be replaced after some time. It becomes necessary to replace the hose when it wears out. Pipe: Solid materials are used to make the pipe. These types of joints appear hard and rigid. tobacco pipe: Pipes are also made of solid materials and have significant hardness. Pipes are less flexible than pipes. The way the parts work and connect in the pneumatic system is different. In fact, this difference in appearance causes the silencer (exhaust) of the aforementioned pneumatic SNB model to appear in various forms. L fittings Some of these connections are L-shaped or elbow. L joints are introduced as angle joints. The angle considered for L connections is 90 degrees. L-shaped pneumatic connections allow multi-purpose or single hoses to be connected. With a pneumatic elbow fitting, the connection of the system can be easily changed by means of a set of pipes. These types of connections are very compact and require little space. Pneumatic fitting is very useful and excellent for working with nylon pipes. Direct connections Pneumatic connections can be of direct type. In direct connections, one direction of the part is connected to the hose or pipe and the other direction is connected to other parts of the system. Bolts and nuts are used to fix these connections. The pneumatic direct fitting acts as an adapter. These fittings are available in different materials, thread sizes, diameters and grades. Direct pneumatic connections can be used with various tools. For this reason, direct connections are used a lot in the pneumatic system. T connection Pneumatic connections can be T-shaped. These connections are used with a pressure mechanism. T-shaped fittings are intended for safe and secure connection to threaded ports and support quick and easy installation without the need for tools. By establishing this connection, the parts can be placed side by side in a three-sided form. The most common application of T-shaped fittings is related to pressure or vacuum applications. The leakage of these T-shaped connections is very low and these connections are designed in the form of a complete hole. Y joints Y-shaped pneumatic joints can be used for various things such as air tools, textile, transportation applications, automotive, industrial airlines, garages, packaging, robotics, etc. Pneumatic Y-shaped connections are introduced with features such as fast disconnection and connection and tank strength against vacuum. and strength of the tank against vacuum are introduced. Functional connections Pneumatic fittings can be divided according to the type of function. The body of the pneumatic fitting can be copper, aluminum, steel, PBT and Bern. Functional pneumatic fittings are used for functions such as shut-off, flow regulation, supply, exhaust and blocking. Communication connections Pneumatic fittings are also classified according to the type of connection. Ball joint Ball pneumatic fitting is used to connect the outer sleeve to the inner fitting. Sleeves are used to disconnect and connect two ends of connections. This type of connection is used for things that require frequent connection and disconnection of the hose. Compressor connection The connections mentioned can be compression or compressor type. In this type of connections, pressure is used to establish the connection. Rings, metal washers and ferrules are used for standard compression and connection. In such a case, the nut is used on the ferrule and pipe for compression. With this nut, it is possible to strengthen and compress the parts together. SP4000 metal flow control with large body Pneumatic fittings are differentiated based on the type of connection and the function they perform. And they are produced in different sizes and types, each of which is used in different uses. Among these connections, we can mention the direct connection, which is available in direct allen-khor, panel direct, plastic bead direct, and direct connection between ways. One of the most widely used pneumatic parts are pneumatic tees. There are different types of tees, tees that feed hoses or tees with hose heads, tees in the middle of the rib and inside the thread, and miniature tees are of this category. The variety of pneumatic connections is very large. In general, connections can be divided into four main parts. 1- Connections with only connection function: This type of connections can be divided into the following two types: 1- Connections with one gear end and one hose end 2- Connections with two hose ends Connections with a gear end and a hose end It is used to connect pneumatic hoses to pneumatic valves or pneumatic manifolds. When buying this type of connection, you should pay attention to the gear size, gear standard, connecting hose size, type of gear (male or female), whether or not it has O-rings, and the physical shape of the connection. SP4000 large body metal flow control Connections with two hose ends It is used to connect two pneumatic hoses to each other or change the connection size. For example, PUC-06 connector is used to connect two size 6 hoses. When buying this type of connection, we should pay attention to the size of the hose and the physical shape of the connection. 2- Connections with special functions: In addition to connecting two parts, this type of connections also have the following special functions. Types of flow controller: Flow controls are used to control flow rate or air flow. One of the important applications of flow control is controlling the movement speed of pneumatic jacks in the industry. Fluocontrollers are available in different types of fluocontrollers (two hose feeding ends) and jack-head fluocontrollers (to connect to pneumatic jacks). SP4000 large body metal flow control Stop fittings: In addition to the connection, these parts act as a one-way valve, and if the hose is placed in it, the air flow is established, and if the hose is removed, the air flow is automatically cut off. In using this connection, you should pay attention to its input and output. When buying, we should pay attention to the size of the hose and its thread. SP4000 large body metal flow control Check Valve: This type of connection is used to make the air path unidirectional. In using this connection, you should pay attention to its input and output. Also, when buying, you should pay attention to the size of the hose and its thread. It should be noted that the maximum working pressure of pneumatic connections is 10 bar, and if the pressure increases more than this value, there is a possibility of leakage and disconnection of the connection. SP4000 large body metal flow control 3- Connections for acidic substances and water: There are also connections, they are completely made of plastic and are used for water and acidic cases. SP4000 large body metallic flow control. 4- Couplings: Couplings are used to temporarily connect two parts of a system. For example, in gas pumps, the fuel nozzle is connected to a coupling, and when refueling, this nozzle is connected to the car's gas tank by the coupling, and after refueling, it is separated from the car. Couplings are available in various sizes and in the form of male and female threads, hose connectors, and you should pay attention to these items when purchasing. SP4000 large body metal flow control. Special features of SP4000 large body metal flow control • The pneumatic fitting can withstand a working pressure of 24 bar according to the size of the design. • The ability to install and use pneumatic system connections is very convenient and easy. For this reason, this SP4000 large-body metal flow control system will be different from other systems. • The rib part of the fittings is made of brass and PBT material can be seen in their body part. • The metal parts of the connections are also plated with nickel or zinc. • NBR O-rings are used to prevent leakage of connections. • Connections of the pneumatic system are supplied in the form of three-way middle rib, swivel knee, straight, etc. This diversity in design causes diversity in the application of flow control in the way The large body of the SP4000 model is also made of metal. • Various types such as NPT, BSPT, METRIC and BSP are used for SP4000 large body metal flow control gears. Important cut when using SP4000 pneumatic large body metal flow control After purchasing the large SP4000 model pneumatic flow control, when using these pneumatic parts, you should pay attention to a series of points and do not use the pneumatic connections in the following conditions: 1- For other uses other than what that particular pneumatic connection was designed and made for. 2- Never touch the release part of the SP4000 pneumatic large body metal flow control when they are under pressure. (Because this will cause the hose to separate and lead to damage). 3- In places where excessive external pressure is applied to the pneumatic connection due to stretching, bending or twisting (because it causes the body of the pneumatic connection to break and create dangerous situations). 4- In places where there is excessive vibration, rotation and bending. 5- In places where SP4000 large body metal pneumatic flow control is exposed to corrosive, inflammable fluid, chemicals, sea water or water vapor. Also, when buying a large-body metal SP4000 pneumatic flow control, you should note that these parts should not be used in machines that are used for purposes such as human life safety, human transportation, or emergency safety tools in general. Use SP4000 pneumatic large body metal flow control only when all impurities such as dust have been removed from them. | Flow control valve with SPC model lock Pneumatic fittings are used to connect different parts of the pneumatic system, hoses and pipes. Pneumatic fittings are stronger and more resistant than hydraulic fittings. For this reason, while connecting parts in pneumatic systems, less pressure is applied to the connections and parts. Pneumatic connections or fittings are used to create a connection between the parts and components of a pneumatic system and circuit. For example, in a pneumatic system that includes a pneumatic valve, a pneumatic jack with speed control, various connections are used to connect these components to each other and to the compressed air of the main inlet. Pneumatic fittings are among the most widely used pneumatic devices that are used to connect and communicate between different components of pneumatic systems. By purchasing SPC pneumatic flow control valve with lock, you will see an increase in the speed of operation in the progress of works and pneumatic systems. Due to the fact that pneumatics are made up of different components, it is obvious that you will need to purchase several pneumatic fittings in different dimensions and features. Similarly, in building water piping, various connections such as elbows, bushings, spools, etc. are used to connect different components (such as pipes to each other, pipes to faucets, etc.). SPC pneumatic flow control valve with lock is made of different materials such as polymer and metal materials (iron with chrome coating and brass). The use of SPC type locking screw flow control Pneumatic connectors are used to connect pneumatic components, and miniature connectors are used to change the inlet air pressure or change its direction. Pneumatic fittings are considered as precise tools in control. Air or pneumatic connections are one of the most important parts in the compressor. Without these parts, you cannot use the air effectively and even if the device is not installed correctly, the compressor may be damaged. We have included the best pneumatic (air) fittings in our product list for your review so that you can find the right part to meet your compressor needs. Flow control valve with SPC model lock Flow control valve with SPC model lock Having a reliable quick connect for air compressors is exactly the difference between a quality compressor and a serious hazard, and can help the consumer increase the compressor's air supply and possibly manage more complex connections. To optimize the life of your equipment, invest in buying high-quality and durable connections. These connections are the link between pipes, hoses and machines. Therefore, having a complete communication is essential for safety. This SPC type locking screw flow control is very suitable for controlling air flow pressure and directional flow. SPC model flow control components with locking head Pneumatic fittings may include parts such as pipes, tubes and hoses. Hose: Layers of different materials are used to make the hose. Hoses are highly flexible and provide suitable conditions for the movement of parts. Hoses need to be replaced after some time. It becomes necessary to replace the hose when it wears out. Pipe: Solid materials are used to make the pipe. These types of joints appear hard and rigid. tobacco pipe: Pipes are also made of solid materials and have significant hardness. Pipes are less flexible than pipes. The way the parts work and connect in the pneumatic system is different. In fact, this difference in appearance leads to the creation of the above-mentioned SPC pneumatic locking head flow control in various forms. L fittings Some of these connections are L-shaped or elbow. L joints are introduced as angle joints. The angle considered for L connections is 90 degrees. L-shaped pneumatic connections allow multi-purpose or single hoses to be connected. With a pneumatic elbow fitting, the connection of the system can be easily changed by means of a set of pipes. These types of connections are very compact and require little space. Pneumatic fitting is very practical and excellent for working with nylon pipes. Direct connections Pneumatic connections can be of direct type. In direct connections, one direction of the part is connected to the hose or pipe and the other direction is connected to other parts of the system. Bolts and nuts are used to fix these connections. The pneumatic direct fitting acts as an adapter. These fittings are available in different materials, thread sizes, diameters and grades. Direct pneumatic connections can be used with different tools. For this reason, direct connections are used a lot in the pneumatic system. T connection Pneumatic connections can be T-shaped. These connections are used with a pressure mechanism. T-shaped fittings are intended for safe and secure connection to threaded ports and support quick and easy installation without the need for tools. By establishing this connection, the parts can be placed side by side in a three-sided form. The most common application of T-shaped fittings is related to pressure or vacuum applications. The leakage of these T-shaped connections is very low and these connections are designed in the form of a complete hole. Y joints Y-shaped pneumatic joints can be used for various things such as air tools, textile, transportation applications, automotive, industrial airlines, garages, packaging, robotics, etc. Pneumatic Y-shaped connectors with features such as quick disconnect and connect and the strength of the tank against vacuum are introduced. Functional connections Pneumatic fittings can be divided according to the type of function. The body of the pneumatic fitting can be copper, aluminum, steel, PBT and Bern. Functional pneumatic fittings are used for functions such as shut-off, flow regulation, supply, exhaust and blocking. Communication connections Pneumatic fittings are also classified according to the type of connection. Ball joint Ball pneumatic fitting is used to connect the outer sleeve to the inner fitting. Sleeves are used to disconnect and connect two ends of connections. This type of connection is used for things that require frequent connection and disconnection of the hose. Compressor connection The connections mentioned can be compression or compressor type. In this type of connections, pressure is used to establish the connection. Rings, metal washers and ferrules are used for standard compression and connection. In such a case, the nut is used on the ferrule and pipe for compression. With this nut, it is possible to strengthen and compress the parts together. Types of flow control with SPC model lock Pneumatic fittings are differentiated based on the type of connection and the function they perform. And they are produced in different sizes and types, each of which is used in different uses. Among these connections, we can mention the direct connection, which is available in direct allen-khor, panel direct, plastic bead direct, and direct connection between ways. One of the most widely used pneumatic parts are pneumatic tees. There are different types of tees, tees that feed hoses or tees with hose heads, tees in the middle of the rib and inside the thread, and miniature tees are of this category. The variety of pneumatic connections is very large. In general, connections can be divided into four main parts. 1- Connections with only connection function: This type of connections can be divided into the following two types: 1- Connections with one gear end and one hose end 2- Connections with two hose ends Connections with a gear end and a hose end It is used to connect pneumatic hoses to pneumatic valves or pneumatic manifolds. When buying this type of connection, you should pay attention to the gear size, gear standard, connecting hose size, gear type (male or female), whether or not it has O-rings, and the physical shape of the connection. Connections with two hose ends It is used to connect two pneumatic hoses to each other or change the connection size. For example, PUC-06 connector is used to connect two size 6 hoses. When buying this type of connection, we should pay attention to the size of the hose and the physical shape of the connection. 2- Connections with special functions: In addition to connecting two parts, this type of connections also have the following special functions. Types of flow controller: Flow controls are used to control flow rate or air flow. One of the important applications of flow control is controlling the movement speed of pneumatic jacks in the industry. Fluocontrols are available in different types of fluocontrols (two hose feeding ends) and jack-head flowcontrols (to connect to pneumatic jacks). Stop fittings: In addition to the connection, these parts act as a one-way valve, and if the hose is placed in it, the air flow is established, and if the hose is removed, the air flow is automatically cut off. In using this connection, you should pay attention to its input and output. When buying, we should pay attention to the size of the hose and its thread. Flow control valve with SPC model lock Check Valve: This type of connection is used to make the air path unidirectional. In using this connection, you should pay attention to its input and output. Also, when buying, you should pay attention to the size of the hose and its thread. It should be noted that the maximum working pressure of pneumatic connections is 10 bar, and if the pressure increases more than this value, there is a possibility of leakage and disconnection of the connection. Flow control valve with SPC model lock 3- Connections for acidic substances and water: There are also connections, they are completely made of plastic and are used for water and acidic things. Flow control with locking head SPC model 4- Couplings: Couplings are used to temporarily connect two parts of a system. For example, in gas pumps, the fuel nozzle is connected to a coupling, and when refueling, this nozzle is connected to the car's gas tank by the coupling, and after refueling, it is separated from the car. Couplings are available in various sizes and in the form of male and female threads, hose connectors, and you should pay attention to these items when buying. Flow control valve with SPC model lock The special features of SPC model flow control valve with lock • The pneumatic fitting can withstand a working pressure of 24 bar according to the size of the design. • The ability to install and use pneumatic system connections is very convenient and easy. For this reason, this flow control with locking SPC model will be different from other systems. • The rib part of the fittings is made of brass and PBT material can be seen in their body part. • The metal parts of the connections are also plated with nickel or zinc. • NBR O-rings are used to prevent leakage of connections. • Connections of the pneumatic system are supplied in the form of three-way middle rib, swivel knee, straight, etc. This diversity in design causes diversity in the application of the SPC model locking head flow control. • There are different types of SPC model locking heads for flow control gears NPT, BSPT, METRIC and BSP are supported. Flow control valve with SPC model lock Flow control valve with SPC model lock Important cut when using SPC pneumatic locking head flow control After purchasing SPC Pneumatic Locking SPC Flow Control, when using these pneumatic parts, you should pay attention to a series of points and do not use pneumatic connections in the following conditions: 1- For other uses other than what that particular pneumatic connection was designed and made for. 2- Never touch the release part of the SPC pneumatic valve when they are under pressure. (Because this will cause the hose to separate and lead to damage). 3- In places where excessive external pressure is applied to the pneumatic connection due to stretching, bending or twisting (because it causes the body of the pneumatic connection to break and create dangerous situations). 4- In places where there is excessive vibration, rotation and bending. 5- In the places where the SPC pneumatic locking head flow control is exposed to corrosive, inflammable fluid, chemicals, sea water or water vapor. Also, when buying a SPC pneumatic locking head flow control, you should note that these parts should not be used in machines that are used for purposes such as human life safety, human transportation, or emergency safety tools in general. Only use SPC pneumatic locking head flow control when all impurities such as dust have been removed from them. | DPSA model digital pressure switchDPSA model digital pressure switch works by combining the mechanical properties of compressed air and electricity. Pneumatic pressurizer is a device for controlling and adjusting pressure that is used in compressed air lines. The switch has the concept of changing the situation, which means that in case of any type of pressure change in the pressure system, the switch controls or secures the situation. This product is one of the precision instrument equipment. Pressure works in two normally open and normally close contacts. In the normally closed state, the contacts are closed in the normal state, when the pressure rises too much, the contacts open in order to reduce the pressure. In the normal open mode, the switch remains open until the pressure exceeds its limit, and the contacts close quickly as the pressure rises. To buy DPSA model digital pressure switch, you should pay attention to things like working pressure range, adjustable maximum pressure, connection size, etc. What is DPSA digital pressure switch or pressure switch? Pneumatic pressure switch or pressure switch is a pressure control switch and is used to adjust the pressure of tanks or prevent pressure increase in pressurized environments in the industry. DPSA model digital pressure switch or pressure controller has an electrical contact and when the pressure reaches At the set value, the contact is activated and an electrical signal is sent and the switch is closed. DPSA model digital pressure switch DPSA model digital pressure switch Also, pressure switches may be designed in such a way that they disconnect or connect the system when the pressure increases or decreases. DPSA model digital pressure switches play an important role in establishing safety and control in pressurized systems, also pressure switches have different types according to usage, working pressure and fluid. How DPSA model digital pressure switch works Normally, pressure switches have a diaphragm filled with air. When the air pressure inside the diaphragm changes, the diaphragm plate changes its shape and causes movement in the calibrated spring connected to it (spring calibration means the previous adjustment of the spring in The required size is the same as the range of the switch). The spring is pushed back by applying pressure and returns to its original position when the pressure is removed. This action is transferred to the electrical contact of the pressure switch and causes the operation of the pressure switch. The spring is set in different ranges for low or high pressures. Depending on the selected range, this spring opens or compresses. Depending on the type of fluid or gas that comes into contact with the diaphragm, the diaphragm has different types, such as: fibrous, plastic, Metal and.. DPSA model digital pressure switches Differential pressure switch Diaphragm switch pressure Capsule pressure switch Diaphragm switch pressure Bellows pressure switch Bardoni pressure switch Piston pressure switch Types of DPSA model digital pressure switch in terms of working fluid Pneumatic Hydraulic DPSA model digital pressure switch This type of pressure switch is an air pressure switch and is one of the simplest types of pressure switches and is mostly used in pneumatic systems or air compressors. Other applications of pneumatic pressure switches include the following: When taking water, it automatically controls the domestic water pump, taking into account the pressure in the pipes. This pressure switch automatically turns off the air compressor when the pressure reaches the set level in the air compressor tank. The pneumatic pressure switch is used to control the charge inside the battery cell. If the pressure in the cockpit becomes too low due to the increase in altitude, it will automatically turn on the warning light in the cockpit of the aircraft. This switch is used to count the traffic of vehicles on the streets and fuel stations using a tube filled with air placed on the floor of the street or work station. Hydraulic pressure switch These types of pressure switches have many uses in cars, for example to warn if the engine oil pressure falls below the safe level. Before the 1960s, pressure switches were used in the hydraulic brake circuit to control the power to the brake light. In newer cars, it uses a switch directly activated by the brake pedal. The types of high-pressure hydraulic switches are as follows: Steam pressure switch gas Explosion Proof Water We will explain it further. Steam switch pressure: Their function is with steam. Steam pressure switches must be able to withstand high temperature and humidity. Steam pressure switches are used to cool water, oil, air and hydrogen fluoride. These types of pressure switches are NC or NO, and when the pressure reaches the set values, the alarm is turned on. Gas switch pressure: In this type of pressure switch, sparking in the electrical part should be prevented as much as possible. Gas pressure switches are also used for flammable gases. Explosion-proof pressure switch: This type of pressure switch is used in cases where there is a risk of fire caused by sparks and flammable gas. The explosion-proof pressure switch enclosure is resistant to sparks and the penetration of environmental gases. Water switch pressure: This type of pressure switch is used in hydraulic industries such as automobiles to display a warning when the engine oil pressure is lower than the acceptable level or to control the automatic locking of the automatic transmission torque. Also, these pressure switches are widely used in water pumps and water supply lines. | Regulator filter model PP4 PP4 model regulator filter is another component of the industrial system. This part is used in places where there are pneumatic systems. The air around us that we breathe has some moisture. When this air is compressed, the moisture along with it is also compressed. The compressed moisture is collected at the bottom of the compressor, but still a large amount of it is transferred by air to the equipment. Moisture seriously damages the equipment. Filters filter this moisture and do not allow moisture and contamination to be transferred to the equipment. The collected water is collected in the filter cup or is drained by the automatic drain. The air that has been filtered must be brought to the right pressure and its pressure must be reduced and actually regulated. The act of regulating is done by the regulator (pressure breaker) and the air is filtered and transferred to the equipment with the right pressure. PP4 model regulator filter sizes Filter regulators are in different sizes and models, which include the following items. 1. The filter sizes of the regulators are: 3", 2", 1", 3/4", 1/2", 3/8", 1/4", 1/8". 2. Drainage of moisture (water) in manual draining models, semi-automatic draining and fully automatic draining. Air regulator filter structure: The air regulator filter consists of several main parts, which include the following: 1. Inlet air adjustment regulator along with wind indicator to observe the inlet air pressure 2. 5 micron fiber or brass filter to capture air moisture and the moisture holding chamber separated from the incoming air 3. The outlet port for the discharge of moisture separated from the inlet air, the filter function of the air regulators: The function of the regulator filter is that the incoming air enters the air adjustment regulator, which can be adjusted from 10 to 0 bar by the air pressure regulator. Regulator filter model PP4 Regulator filter model PP4 Then, after passing through the regulator, the incoming air enters the 5 micron dehumidifier filter and is separated by the incoming air humidity filter, and the dry air without any moisture is directed to the regulator filter outlet and then transferred to the ventilation system. Filter regulator model PP4 or Filter Regulator is one of the industrial parts in the important care unit that is used in many small and large industries. The accuracy and application of standards are important indicators of any industry, and in better words, the lack of these two indicators can create important challenges and disturbances. Industry and engineering have a direct and continuous relationship with each other, and since the accuracy of measurement in engineering is one of the most important discussions, as a result, in industry, which is dependent on engineering plans, measurement and accuracy in doing it are very important. In the industry, the more accurate the measurement, the less the percentage of errors and the higher the efficiency and also the success of the project. In other words, in the industry and production, there are indicators and standards that must be followed seriously. To comply with these standards, specialized companies are working all over the world and each of them produces special parts. In simpler terms, various tools are designed to apply accurate measurements in industries, and several pieces together manage and control a part of an industry. The scope of diversity of measuring instruments in industries is very large. Some of these tools have the ability to measure instantaneously, and by using today's technologies, such as digital data, they announce instantaneous measurement, and some other instruments have mechanical functions, but they are designed and produced based on engineering principles. Standard working conditions of filter regulator model PP4 The regulator filter can be used at a temperature of +40 to -5 degrees Celsius and with a fluid pressure of 10 to 0 bar. Note that if the incoming air is stained with oil or grease, the dehumidifier filter will be greased and unable to absorb moisture. Uses of PP4 model regulator filter: The reason for using filter regulators in the ventilation system is to separate moisture from the air, because if the air used contains moisture, it will cause irreparable problems, which we will mention a few of: 1. Rotting and loss of all O-rings and packings in the air steering jacks and valves and oxidation, rotting and rusting of the body of the air steering jacks and valves. 2. In the paint industry, we can mention the creation of water holes, the unevenness of the paint surface and many different problems. He pointed out in machine building, food, pharmaceutical, health, construction, oil, gas, petrochemical and other industries. Criteria for the regulator filter stone material: Filter material (brass filter-felt filter) Filter micronization (from forty microns to one hundredth of a micron) Appearance and dimensions of the filter Usually, filter stone (filter element) with 40 or 20 micron is used in the filter of existing regulators. 20 micron stone is used in felt filters. Definition of Prerequisite Care Unit Introduction of Filter Regulator The filter regulator is one of the parts used in the maintenance unit of pneumatic systems. In this article, the care unit is the same as the pneumatic care unit, and we intend to introduce one of the most important parts of this section, the regulator filter. Pneumatic systems are used in various industries and in industrial machines. Pneumatic systems, like their importance, are sensitive to different conditions, including polluted and humid air, and they must be supplied with healthy air in order to have proper efficiency, for this reason, different parts are used to create suitable conditions, and their collection is called a care unit. | ||||||||||||
| Weight | n. v. | n. v. | n. v. | n. v. | n. v. | n. v. | ||||||||||||
| Dimensions | n. v. | n. v. | n. v. | n. v. | n. v. | n. v. | ||||||||||||
| Additional information |
|
|
|
|
|
|
Related products
● Space saving · 10mm width
Easy settings
Use the key button to adjust the valve
● Fast response time
Output response time less than 1.5 milliseconds
● This product turns compressed air on/off on compressed air devices by just turning the knob.
● Once the residual pressure in the device is removed, maintenance or inspection is possible
● A three-way valve relieves residual pressure and blocks the intake air.
• Application for hydraulic, pneumatic, semi-conductor, CNC machine, oxygen generator, compressor, chemical plant and power plant parts, etc. Control the pressure automatically.
Compact design
•Lightweight
- Speed controller with internal pilot check valve
- Easy to control cylinder speed
● ONE ACTION inserts tube for easy attachment and release
● The volume and OD are smaller than the conventional type, but the same flux is obtained
● Surface treated with electroless nickel plating for excellent corrosion resistance
● The oval sleeve is designed to be easily released in confined spaces
● The screw part has O-rings or has a sealant coating
● Small fittings for small appliances and piping in confined spaces
liquid air
Maximum operating pressure (MPa) 1.0 (140psi)
Constant pressure (MPa) 1.5 (200psi)
Standard pressure setting 0.05~1.0 (7~140psi)
(MPa) Customized specifications 0.05~0.2 (7~30psi), 0.05~0.4 (7~60psi), 0.05~1.2 (7~170psi)
Ambient and fluid temperature (℃) -5 ~ 60 (23 ~ 140 °F) (non-freezing)
Flow capacity ※ 1/4˝ 2100 (74scfm)
(Nℓ/min) 3/8˝ 2,600 (92scfm)
Filtration (㎛) 5
Soothing style of construction
Polycarbonate bowl material
Nylon bowl protective material
Discharge Capacity (㎤) Manual Drain: 38 (1.28 oz), Auto Discharge: 30 (1.01 oz)
Weight (kg) 0.49 (1.08 lbs)
Bewertungen
Es gibt noch keine Bewertungen.